Abstract:As a novel high-entropy ceramic material with a multi-cation and multi-anion sublattice structure, high-entropy carbonitride ceramics (HECNs) have exhibited outstanding comprehensive properties and attracted increasing attention. In this study, a new WC-based cemented carbide material reinforced by high-entropy carbonitride (Ti 0.2 W 0.2 Mo 0.2 V 0.2 Nb 0.2 )(C 0.7 N 0.3 ) (marked as HECN) was successfully fabricated by vacuum hot-pressed sintering. The mutual constraints between hardness and fracture toughness in extant WC-Co cemented carbide tool materials and their deficient high-temperature mechanical properties were effectively addressed. Moreover, for the low efficiency of the traditional carbothermal reduction nitridation, a novel method for rapidly preparing HECN powder was firstly proposed, namely the microwave-assisted carbothermal reduction nitridation, which could accelerate the heating rate and shorten the holding time. Single-phase HECN powder was successfully synthesized by this method, and the impacts of varying HECN content on the room and high-temperature mechanical properties of WC-based cemented carbide were investigated combined with the microstructure analysis by XRD\SEM. The results revealed that HECN effectively inhibited the grain growth of WC in cemented carbide, and the refined WC grains provided a high-volume fraction of grain boundaries, which prevented dislocation movement and increased the hardness. With the optimized HECN content of 10 wt%, the Vickers hardness and fracture toughness of WC-HECN-Co composite reached 21.58 ± 0.36 GPa and 12.27 ± 1.17 MPa∙m 1/2 respectively. Furthermore, WC-10HECN-10Co composites possessed outstanding high-temperature hardness and maintained a high hardness value of 13.16 ± 0.30 GPa at 800 °C, 37% higher than that of WC-10Co. The findings of this research hold significant practical implications for applying cemented carbide cutting tools in high-speed dry cutting.

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

High-gravity Combustion Synthesis and in Situ Melt Infiltration: A New Method for Preparing Cemented Carbides

Sintering behavior of WC-10Co-V(C, N) nanocrystalline gradient cemented carbide

Preparation of nanocrystalline gradient cemented carbide by adding gradient former of V(C, N)

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

Effect of initial WC particle size on grain growth behavior and gradient structure formation of bilayer functionally graded cemented carbides

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Fabrication of Hard Cermets by In-Situ Synthesis and Infiltration of Metal Melts into WC Powder Compacts

Preparation of a novel dual structure graded cemented carbides induced by bidirectional diffusion

Comparison of the microstructure and mechanical properties of WC-Ti(C, N)-Ni gradient cemented carbides prepared by SPS pre-sintering and vacuum pre-sintering

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

Effect of the nitrogen multi-sources on the microstructure and hardness of the graded surface layer in WC–Co–Cubic cemented carbides

Fabrication of Ni/WC composite with two distinct layers through centrifugal infiltration combined with a thermite reaction

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

Fabrication and Micro-Structure of a Multilayer Functionally Graded (wc–co)–ni Composite

Preparation of WC/CoCrFeNiAl0.2 high-entropy-alloy composites by high-gravity combustion synthesis