Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Preparation of nanocrystalline gradient cemented carbide by adding gradient former of V(C, N)

Sintering behavior of WC-10Co-V(C, N) nanocrystalline gradient cemented carbide

Role of V(C, N) on gradient structure formation and mechanical properties of nanocrystalline cemented carbides

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Comparison of the microstructure and mechanical properties of WC-Ti(C, N)-Ni gradient cemented carbides prepared by SPS pre-sintering and vacuum pre-sintering

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Preparation of a novel dual structure graded cemented carbides induced by bidirectional diffusion

Effect of initial WC particle size on grain growth behavior and gradient structure formation of bilayer functionally graded cemented carbides

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Effect of the nitrogen multi-sources on the microstructure and hardness of the graded surface layer in WC–Co–Cubic cemented carbides

Effect of MWCNTs on microstructure and properties of WC-9Co gradient cemented carbides

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Effects of nanocomposite grain growth inhibitors and multi-walled carbon nanotubes on the microstructure and mechanical properties of ultrafine cemented carbides

Ultrafine/nano WC-Co Cemented Carbide: Overview of Preparation and Key Technologies

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

A short and facile process to synthesize WC-Co cemented carbides

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides

Enhancement of the mechanical properties of ultrafine-grained WC-Co cemented carbides via the in-situ generation of VC