Abstract:Replacement of Co by alternative Ni binder in gradient cemented carbide is an effective way to reduce the health concerns associated with Co powders. In the present work, gradient cemented carbides with different Ni contents and gradient sintering times were prepared by traditional powder metallurgy with a two-step sintering method. The microstructure of cemented carbide including the gradient layer formation was analyzed by XRD, SEM, EDS, TEM, and EBSD. The thickness of the gradient layer is almost proportional to the square root of sintering time, indicating that the gradient layer formation is a diffusion-controlled process. The atomic migration can be accelerated to form a thicker gradient layer with the increase of the binder content. The coherent interface of the Ti(C, N) core-rim structure for the gradient cemented carbides with Ni binder was revealed. With the increase in binder content, the average grain size of the WC phase is increased. The hardness and fracture toughness of the cemented carbides were also studied and analyzed according to the crack propagation behavior and the distribution of dislocation and stress indicated by KAM and GND. The variation of the hardness and the fracture toughness with the sintering time is mainly related to the density and the grain size of hard phases, while the change of the mechanical properties along with the Ni content probably results from the local dislocation density and the stress in the cemented carbides. The cemented carbide can obtain a good combination of hardness and fracture toughness with 10 wt% Ni gradient sintered for 2h.

Effect of the nitrogen multi-sources on the microstructure and hardness of the graded surface layer in WC–Co–Cubic cemented carbides

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Relation between the nitrogen gas pressure and structure characteristics of WC–Ti(C, N)–Co graded cemented carbides

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Effect of initial WC particle size on grain growth behavior and gradient structure formation of bilayer functionally graded cemented carbides

Sintering behavior of WC-10Co-V(C, N) nanocrystalline gradient cemented carbide

Development of multilayer graded cemented carbides with Ti–Zr carbonitride miscibility gaps

Effect of MWCNTs on microstructure and properties of WC-9Co gradient cemented carbides

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

Effects of nanocomposite grain growth inhibitors and multi-walled carbon nanotubes on the microstructure and mechanical properties of ultrafine cemented carbides

Role of V(C, N) on gradient structure formation and mechanical properties of nanocrystalline cemented carbides

Preparation of a novel dual structure graded cemented carbides induced by bidirectional diffusion

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of carbon content on the properties of inhomogeneous cemented carbides with fine-grained structures produced via one-step transformation

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Effect of carbon content on the microstructure and properties of Cr-doped WC–15Co cemented carbide

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides