Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Preparation of a novel dual structure graded cemented carbides induced by bidirectional diffusion

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Development of multilayer graded cemented carbides with Ti–Zr carbonitride miscibility gaps

Effect of initial WC particle size on grain growth behavior and gradient structure formation of bilayer functionally graded cemented carbides

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Preparation of nanocrystalline gradient cemented carbide by adding gradient former of V(C, N)

Effect of the nitrogen multi-sources on the microstructure and hardness of the graded surface layer in WC–Co–Cubic cemented carbides

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Two-material Powder Injection Molding of Functionally Graded WC–Co Components

Sintering behavior of WC-10Co-V(C, N) nanocrystalline gradient cemented carbide

Preparation,Microstructure and Performance of WC-Ni Reinforced Fe-based Graded Coating

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

Comparison of the microstructure and mechanical properties of WC-Ti(C, N)-Ni gradient cemented carbides prepared by SPS pre-sintering and vacuum pre-sintering

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

Study on the Properties of Coated Cutters on Functionally Graded WC-Co/Ni-Zr Substrates with FCC Phase Enriched Surfaces

Role of Co Content on Densification and Microstructure of WC–Co Cemented Carbides Prepared by Selective Laser Melting

A short and facile process to synthesize WC-Co cemented carbides

High-temperature Mechanical Behavior of Ultra-Coarse Cemented Carbide with Grain Strengthening