Abstract:Ultra-high toughness and ultra-high hardness WC-10Co-xAl(2)O(3) cemented carbides were successfully prepared by vacuum liquid phase sintering (VS) and spark plasma sintering (SPS) using ultrafine WC and commercial Co powders as raw materials, respectively. The effects of nano-Al2O3 content and sintering process on the relative density, average grain size, microstructure and mechanical properties of WC-10Co alloys were investigated. The results showed that the densification degree of the samples decreased with the increase of Al2O3 content. In addition, the relative densities of the samples prepared by SPS were lower than those of the samples prepared by VS. For the samples prepared by VS, the average grain size increased first and then decreased as the Al2O3 content increased from 3 wt% to 9 wt%, and the percentage of coarse grain showed the same trend. When the addition of Al2O3 was 6 wt%, the average grain size reached the maximum value of 1.39 +/- 1.03 mu m. Meanwhile, the sample with 6 wt% Al2O3 had a typical inhomogeneous dual-grain structure, and the percentages of fine grain (< 1 m) and coarse grain (> 1 mu m) were about 50%, which displayed the highest fracture toughness of 18.59 MPa center dot m(1/2). The dual-grain structure not only improved the toughness, but also compensated the loss of hardness. However, for the samples prepared by SPS, with the increase of Al2O3 content, the average grain size of WC decreased, while both hardness and toughness were continuously improved. When the Al2O3 content increased to 9 wt%, the grain size reached the minimum value of 0.25 +/- 0.08 mu m, and meanwhile, the hardness and toughness reached the maximum value of 19.69 GPa and 12.29 MPa center dot m(1/2), respectively. Moreover, as the Al2O3 content increased, the transverse rupture strength (TRS) of the samples prepared by VS increased first and then decreased, and the TRS of sample with 3 wt% Al2O3 reached the maximum value of 1410 MPa. However, the TRS of the sample prepared by SPS showed a decreasing trend.

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Effect of titanium addition on microstructure and mechanical properties of WC-Ni<sub>3</sub>Al cemented carbide br

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Effects of NbC/VC Addition on Mechanical Properties of Ultrafine Grained Cemented Carbides

Ultrafine WC-Ni cemented carbides fabricated by spark plasma sintering

Effect of Vc and Nbc Additions on Microstructure and Properties of Ultrafine Wc-10co Cemented Carbides

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Research of carbon addition of pressure sintering superfine WC-0.27VC-0.53Cr3C2 cemented carbide

Effects of Nano-Al2O3 Additions on Microstructures and Properties of WC-8Co Hard Metals

Effect of VC, TaC and NbC Additions on Microstructure and Properties of Ultrafine WC-10%Co Cemented Carbides

Effect of Carbon Content on the Microstructure and Mechanical Properties of Ultrafine WC-15Co Cemented Carbides Using a Co-based Solid Solution Binder Phase

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effects of Composite Binder Phase on Microstructure and Mechanical Properties of Ultrafine‐grained Cemented Carbides

Effects of nano-alumina on mechanical properties and wear resistance of WC-8Co cemented carbide by spark plasma sintering

Effects of Small Amount of Cobalt Addition on Densification and WC Grain Growth during Sintering of Binderless Cemented Tungsten Carbide

Effect of Carbon Nanotubes Additives on Mechanical Properties of WC-6Co Cemented Carbide

Effects of (ti,ta,nb,w)(c,n) on the Microstructure, Mechanical Properties and Corrosion Behaviors of WC-Co Cemented Carbides

Effect of SiC Nano-Whisker Addition on WC–Ni Based Cemented Carbides Fabricated by Hot-Press Sintering

Effects of Sintering Method and Al2O3 Content on Microstructure and Mechanical Properties of WC-10Co Cemented Carbide

Effects of Nano-Al2o3 and Nano-Zro2 on the Microstructure, Behavior and Abrasive Wear Resistance of WC-8Co Cemented Carbide