Abstract:Refractory metal carbides TiC, ZrC, HfC, NbC and TaC have excellent physical, chemical and mechanical properties as materials for ultra-high temperature ceramics. Of these, the most refractory are TaC and HfC, whose melting points approach 4000°C. It should be noted the high hardness, strength and wear resistance of refractory carbides. Hence, there is a natural interest in high-entropy carbides based on them, which are becoming an important class of new ceramic materials, since they potentially have more advanced applied properties. However, obtaining such materials by classical metallurgical methods is a difficult task. In modern research, samples of high-entropy carbides are most often synthesized using expensive special equipment (methods of plasma-spark sintering, high-energy planetary mills, etc.) and a relatively long preparation of precursors for sample production. This paper describes a new approach to the synthesis of multicomponent carbide (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C using an electrochemical process at a temperature not exceeding 1173 K. The method is based on the phenomenon of currentless metal transfer in molten salts. After the step-by-step transfer of metals, the sample was washed from the electrolyte, then sintered in a vacuum furnace. According to X-ray phase analysis, the resulting high-entropy carbide is a single-phase solid solution with an FCC structure. The diffraction pattern of the synthesized sample is in good agreement with the calculated diffraction pattern obtained by the Debye formula for a supercell of 64 000 atoms. A compact sample of high-entropy carbide was produced by pressing a tablet 10 mm in diameter with the addition of cobalt as a matrix metal. After vacuum sintering, the sample was ground to prepare for examination on a scanning electron microscope. Elemental mapping of the sample surface was performed, which showed a satisfactory distribution of metals that make up the high-entropy carbide. The measured microhardness of the sample turned out to be less than the values found in the publications of other authors, which may be due to some residual sample porosity.

High-gravity Combustion Synthesis and in Situ Melt Infiltration: A New Method for Preparing Cemented Carbides

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

Fabrication of Hard Cermets by In-Situ Synthesis and Infiltration of Metal Melts into WC Powder Compacts

Fabrication of Cu-riched W-Cu composites by combustion synthesis and melt-infiltration in ultrahigh-gravity field

Low temperature pressureless immediate sintering of novel nanostructured WC/Co/NiCrSiB-alloy cemented carbide

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

High-gravity Combustion Synthesis of W-Cr Alloys with Improved Hardness

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

In-situ Combustion Synthesis and Densification of TiC–xNi Cermets

The Preparation Process, Microstructure and Properties of Cellular TiC-High Mn Steel-Bonded Carbide

Additive Manufacturing of Cemented Carbides Inserts with High Mechanical Performance

Combustion synthesis and densification of large-scale TiC–xNi cermets

A short and facile process to synthesize WC-Co cemented carbides

Microstructure and mechanical properties regulation and control of in-situ TiC reinforced CoCrFeNiAl0.2 high-entropy alloy matrix composites via high-gravity combustion route

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

High-gravity Combustion Synthesis: A Fast and Furnace-Free Way for Preparing Bulk Ceramic Materials

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

PRODUCING METHOD OF HIGH ENTROPY CARBIDE IN AN IONIC MELT

Self-propagating high-temperature synthesis of TiC-TiB2/Cu ceramic-matrix composite