Abstract:The study covers the method of azide self-propagating high-temperature synthesis (SHS-Az) to obtain a highly dispersed TiN–SiC ceramic composite with a theoretical ratio of nitride and carbide phases from 1 : 4 to 4 : 1 (in moles) using the combustion of the corresponding composition of powder reagent mixtures: NaN 3 sodium azide, (NH 4 ) 2 TiF 6 , (NH 4 ) 2 SiF 6 and Na 2 SiF 6 halide salts, titanium, silicon and carbon in a nitrogen gas atmosphere. Thermodynamic calculations using the Thermo computer program showed that the optimum nitrogen pressure in the reactor is about 4 MPa, and the final composition of SHS-Az products can be completely different depending on the composition of reagents: it may include only target phases (TiN–SiC), contain silicon nitride and free carbon phases impurities (TiN–SiC–Si 3 N 4 –C) along with the target phases or consist only of nitride and free carbon phases (TiN–Si 3 N 4 –C). It was found that only target TiN and SiC phases are formed when using halide salt (NH 4 ) 2 TiF 6 , at any ratio of nitride and carbide phases in the final powder composition. In cases where halide salts (NH 4 ) 2 SiF 6 and Na 2 SiF 6 are used, target TiN and SiC phases are synthesized with an increased titanium content in reagents, i.e. only when composites of the 2TiN–SiC and 4TiN–SiC with an increased content nitride phase are obtained. Experimental studies of combustion products using scanning electron microscopy, energy dispersion analysis and X-ray phase analysis showed that they differ significantly from the theoretical compositions of products by the completely absent or significantly reduced SiC phase content in the final composition of powder composites synthesized during the combustion of bulk charge with carbon, and at the same time the absence of free carbon in the final composition of powder composites obtained. This difference is explained by the fact that when the combustion of a silicon and carbon powder mixture is initiated, silicon nitride is synthesized at the first stage with the temperature rising to high values of about over 1900 °C, at which the synthesized Si3N4 dissociates, and then at the second stage the resulting silicon reacts with carbon to form SiC that is more stable at high temperatures. But during combustion, very small light particles of carbon black (soot) may be removed (blown out) from a burning highly porous charge sample of bulk density by gases released at the first stage of combustion and not participate in the transformation of Si 3 N 4 into SiC. In this regard, in case of low-carbon charge combustion, silicon carbide either does not form at all, or it is formed in small quantities compared to the theoretically possible amount, and Si 3 N 4 silicon nitride remains the main component of the composite. A noticeable amount of SiC is formed only when burning high-carbon charges, but this amount is significantly less than the possible theoretical one, and the difference between them is replaced by the silicon nitride content. Therefore, it was experimentally shown for the first time that the SHS process can be used to obtain composites of highly dispersed ceramic powders TiN–Si 3 N 4 and TiN–Si 3 N 4 –SiC consisting of a mixture of nanoscale (less than 100 nm) and submicron (100 to 500 nm) particles with a relatively low content of free silicon admixture (less than 1.4 %).

Synthesis of Casting Composite Materials Based on Tungsten Carbides with Nickel Binding by the SHS Metallurgy Method

Synthesis of Cast Composite Materials by SHS Metallurgy Methods

SYNTHESIS OF COMPOSITE POWDERS «TIC – NICRBSI ALLOY BINDER» FOR CLADDING AND DEPOSITION OF WEAR-RESISTANT COATINGS

High-gravity Combustion Synthesis and in Situ Melt Infiltration: A New Method for Preparing Cemented Carbides

Fabrication of Cu-riched W-Cu composites by combustion synthesis and melt-infiltration in ultrahigh-gravity field

The Effect of the Nickel Content and Mechanical Activation on Combustion in the 5Ti + 3Si + xNi System

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Effect of a NiO Additive on Interaction in a Ni–Al–W System in Self-Propagating High-Temperature Synthesis

Azide self-propagating high-temperature synthesis of highly dispersed TiN–SiC ceramic nitride-carbide powder composites

Preparation of NiAl-AlMg6 Functionally Graded Composite Using the Energy of a Highly Exothermic Ti-C Mixture during Self-Propagating High-Temperature Synthesis

Synthesis of Al2O3-WSi2-WB2-WB composite in Al-Si-WO3-B2O3 system by self-propagating high-temperature synthesis

SHS Compaction of TiC-Based Cermets Using Mechanically Activated Mixtures

Structure and Phase Composition of SHS Products in Powder Mixtures of Titanium, Carbon, and Aluminum

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Structure and Properties of WC-Fe-Ni-Co Nanopowder Composites for Use in Additive Manufacturing Technologies

Synthesis and Sintering of Tungsten and Titanium Carbide: A Parametric Study

Novel synthesis of CuW composite reinforced with lamellar precipitates via aluminothermic reduction

Tailoring the Composition and Structure of Nb-, Si-, and B-Doped Mo-Based Composite Materials in the Self-Propagating High-Temperature Synthesis Metallurgy Process

Enhanced properties of hard metal WC-Ni processed from nanostructured powders

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

The Effect of the Cobalt Content and Mechanical Activation on Combustion in the Ni + Al + Co System