Abstract:As a novel high-entropy ceramic material with a multi-cation and multi-anion sublattice structure, high-entropy carbonitride ceramics (HECNs) have exhibited outstanding comprehensive properties and attracted increasing attention. In this study, a new WC-based cemented carbide material reinforced by high-entropy carbonitride (Ti 0.2 W 0.2 Mo 0.2 V 0.2 Nb 0.2 )(C 0.7 N 0.3 ) (marked as HECN) was successfully fabricated by vacuum hot-pressed sintering. The mutual constraints between hardness and fracture toughness in extant WC-Co cemented carbide tool materials and their deficient high-temperature mechanical properties were effectively addressed. Moreover, for the low efficiency of the traditional carbothermal reduction nitridation, a novel method for rapidly preparing HECN powder was firstly proposed, namely the microwave-assisted carbothermal reduction nitridation, which could accelerate the heating rate and shorten the holding time. Single-phase HECN powder was successfully synthesized by this method, and the impacts of varying HECN content on the room and high-temperature mechanical properties of WC-based cemented carbide were investigated combined with the microstructure analysis by XRD\SEM. The results revealed that HECN effectively inhibited the grain growth of WC in cemented carbide, and the refined WC grains provided a high-volume fraction of grain boundaries, which prevented dislocation movement and increased the hardness. With the optimized HECN content of 10 wt%, the Vickers hardness and fracture toughness of WC-HECN-Co composite reached 21.58 ± 0.36 GPa and 12.27 ± 1.17 MPa∙m 1/2 respectively. Furthermore, WC-10HECN-10Co composites possessed outstanding high-temperature hardness and maintained a high hardness value of 13.16 ± 0.30 GPa at 800 °C, 37% higher than that of WC-10Co. The findings of this research hold significant practical implications for applying cemented carbide cutting tools in high-speed dry cutting.

Fabrication of Hard Cermets by In-Situ Synthesis and Infiltration of Metal Melts into WC Powder Compacts

Achieving hardness‐strength‐toughness synergy in (Ti, W, Mo, Cr)(C, N)‐based cermets

Ultra-High Hardness TiC-W-Ni Cermets Prepared by Spark Plasma Sintering of Ultra-Fine TiC Powder

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

High-gravity Combustion Synthesis and in Situ Melt Infiltration: A New Method for Preparing Cemented Carbides

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

Dual-grained Mo2FeB2-based cermets containing WC fabricated via multi-step sintering approach: Microstructure, mechanical properties and interface characteristics

Fabrication, microstructure evolution, and mechanical properties of Ti(C,N)-HfN-WC-Ni-Mo cermets

Production of high-property Cr3C2-based cermet with Cr3C2–10WC composite powder as starting material

Liquid phase assisted synthesis of (Ti,V,Nb,Ta,W)C-Ni high entropy carbide cermets by conventional pressureless sintering

Cemented Tungsten Carbide Hardmetal-An Introduction

Correlation between microstructure and mechanical properties of Ti(C,N)-xWC-Ni cermets prepared by mechanical activation and subsequent in situ carbothermal reduction

Microstructure and Mechanical Properties of Ultrafine WC–Ni–VC–TaC–cBN Cemented Carbides Fabricated by Spark Plasma Sintering

Enhanced Coarse-Grained WC-Co(Ce) Cemented Carbide Prepared through Co-Precipitation

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Fabrication of Ni/WC composite with two distinct layers through centrifugal infiltration combined with a thermite reaction

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

Microstructure and properties of WC-12Co cemented carbide fabricated via selective electron beam melting

Effect of Cold Isostatic Pressing and VC Grain Growth Inhibitor Addition on WC Grain Size and Mechanical Properties of WC-8Co Cemented Carbide