Abstract:As a novel high-entropy ceramic material with a multi-cation and multi-anion sublattice structure, high-entropy carbonitride ceramics (HECNs) have exhibited outstanding comprehensive properties and attracted increasing attention. In this study, a new WC-based cemented carbide material reinforced by high-entropy carbonitride (Ti 0.2 W 0.2 Mo 0.2 V 0.2 Nb 0.2 )(C 0.7 N 0.3 ) (marked as HECN) was successfully fabricated by vacuum hot-pressed sintering. The mutual constraints between hardness and fracture toughness in extant WC-Co cemented carbide tool materials and their deficient high-temperature mechanical properties were effectively addressed. Moreover, for the low efficiency of the traditional carbothermal reduction nitridation, a novel method for rapidly preparing HECN powder was firstly proposed, namely the microwave-assisted carbothermal reduction nitridation, which could accelerate the heating rate and shorten the holding time. Single-phase HECN powder was successfully synthesized by this method, and the impacts of varying HECN content on the room and high-temperature mechanical properties of WC-based cemented carbide were investigated combined with the microstructure analysis by XRD\SEM. The results revealed that HECN effectively inhibited the grain growth of WC in cemented carbide, and the refined WC grains provided a high-volume fraction of grain boundaries, which prevented dislocation movement and increased the hardness. With the optimized HECN content of 10 wt%, the Vickers hardness and fracture toughness of WC-HECN-Co composite reached 21.58 ± 0.36 GPa and 12.27 ± 1.17 MPa∙m 1/2 respectively. Furthermore, WC-10HECN-10Co composites possessed outstanding high-temperature hardness and maintained a high hardness value of 13.16 ± 0.30 GPa at 800 °C, 37% higher than that of WC-10Co. The findings of this research hold significant practical implications for applying cemented carbide cutting tools in high-speed dry cutting.

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

L1 2 strengthening of WC-CoNiFe cemented carbides by spark plasma sintering

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Low temperature pressureless immediate sintering of novel nanostructured WC/Co/NiCrSiB-alloy cemented carbide

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Spark Plasma Sintering of Ultrafine WC-5%Co Cemented Carbide Composite Powders

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

Microstructure and properties of WC-Co/CrMnFeCoNi composite cemented carbides

Fabrication of Hard Cermets by In-Situ Synthesis and Infiltration of Metal Melts into WC Powder Compacts

WC-based cemented carbide with NiFeCrWMo high-entropy alloy binder as an alternative to cobalt

Microstructure and Mechanical Properties of Ultrafine WC–Ni–VC–TaC–cBN Cemented Carbides Fabricated by Spark Plasma Sintering

Production of high-property Cr3C2-based cermet with Cr3C2–10WC composite powder as starting material

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering