Abstract:As a novel high-entropy ceramic material with a multi-cation and multi-anion sublattice structure, high-entropy carbonitride ceramics (HECNs) have exhibited outstanding comprehensive properties and attracted increasing attention. In this study, a new WC-based cemented carbide material reinforced by high-entropy carbonitride (Ti 0.2 W 0.2 Mo 0.2 V 0.2 Nb 0.2 )(C 0.7 N 0.3 ) (marked as HECN) was successfully fabricated by vacuum hot-pressed sintering. The mutual constraints between hardness and fracture toughness in extant WC-Co cemented carbide tool materials and their deficient high-temperature mechanical properties were effectively addressed. Moreover, for the low efficiency of the traditional carbothermal reduction nitridation, a novel method for rapidly preparing HECN powder was firstly proposed, namely the microwave-assisted carbothermal reduction nitridation, which could accelerate the heating rate and shorten the holding time. Single-phase HECN powder was successfully synthesized by this method, and the impacts of varying HECN content on the room and high-temperature mechanical properties of WC-based cemented carbide were investigated combined with the microstructure analysis by XRD\SEM. The results revealed that HECN effectively inhibited the grain growth of WC in cemented carbide, and the refined WC grains provided a high-volume fraction of grain boundaries, which prevented dislocation movement and increased the hardness. With the optimized HECN content of 10 wt%, the Vickers hardness and fracture toughness of WC-HECN-Co composite reached 21.58 ± 0.36 GPa and 12.27 ± 1.17 MPa∙m 1/2 respectively. Furthermore, WC-10HECN-10Co composites possessed outstanding high-temperature hardness and maintained a high hardness value of 13.16 ± 0.30 GPa at 800 °C, 37% higher than that of WC-10Co. The findings of this research hold significant practical implications for applying cemented carbide cutting tools in high-speed dry cutting.

WC-based cemented carbide with NiFeCrWMo high-entropy alloy binder as an alternative to cobalt

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Structure and Mechanical Properties of WC-Based Hardmetal with a High-Entropy NiFeCrWMo Binder

WC-Based Cemented Carbides with High Entropy Alloyed Binders: A Review

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

The Effect of Carbon Content on the Microstructure and Mechanical Properties of Cemented Carbides with a CoNiFeCr High Entropy Alloy Binder

Insight into Grain Refinement Mechanisms of WC Cemented Carbide with Al0.5CoCrFeNiTi0.5 Binder

Microstructure and properties of WC-Co/CrMnFeCoNi composite cemented carbides

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

“Effect of tungsten carbide (WC) on electrochemical corrosion behavior, hardness, and microstructure of CrFeCoNi high entropy alloy”

Structure and Properties of WC-Fe-Ni-Co Nanopowder Composites for Use in Additive Manufacturing Technologies

Simultaneous enhancements of strength and hardness for fine-grained W-NiFeCoCrMn composites

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Microstructure and Properties of CoCrFeNi(WC) High-Entropy Alloy Coatings Prepared Using Mechanical Alloying and Hot Pressing Sintering

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering