Abstract:A possible way to realize a 22.5 nm 1⁄2 pitch and beyond BEOL interconnect structures within the low-k material is the partial-trench via first with self-aligned double patterning (SADP) integration approach. A scheme of this BEOL integration stack with the different materials used after patterning is described in Figure 1. In BEOL processing, fluorocarbon-containing plasma is commonly used to pattern silica-based dielectric layers. During the patterning of the low-k dielectric layer, a thin layer of fluoropolymer (CFx-type residues) is intentionally deposited on the dielectric sidewalls and TiN hardmask to ensure anisotropic etching and prevent/minimize dielectric degradation. This polymer layer must be removed from the sidewall and the via bottom prior to the subsequent processing steps to achieve good adhesion and coverage of materials deposited in the etched features. The compatibility requirement is even more stringent for advanced low-k dielectrics, i.e. materials with lower k-value and higher porosity. The post etch residue (PER) amount and properties are specific and depend on the stack structure and the plasma that is used for patterning. The low-k materials and hardmasks that are used in this work are respectively an organo-silicate glass (OSG) type of low-k material with k = 2.4 (~20 % open porosity) and low-stress TiN. Recent results clearly showed the presence of a highly fluorinated layer deposited on the trench sidewalls during the plasma etch based on a fluorocarbon plasma [1-3]. Commodity aqueous cleaning solutions, such as diluted HF, do not efficiently remove the sidewall polymers without etching the underlying layer (lift-off). Therefore, there is a need for commercially available chemicals that can be easily tuned to deal with the different requirements. This study focuses on the use of FOTOPUR® R 2300 mixed with H2O2 for polymer residue removal selectively to other materials (presented in the stack) such as MHM, metals (Cu, W), and porous low-k dielectrics. We will show that TiN etch can be easily tuned by changing the concentration of H2O2.

Research on K9 Glass Wet Etching for MOEMS Devices

SEM Research of SiO2 Thin Film on Inner Wall of Glass Container by PECVD

Investigation of Amorphous Silicon As Dry Etch Hard Mask in BEOL Low-k Dielectric Patterning

Wet etching in beta-Ga2O3 bulk single crystals

Pyrex Glass Wet Deep Etching and Surface Wiring

Research on Metal Protection in KOH Wet Etching Process

Wet Etching in β-Ga2O3 Bulk Single Crystal

Monomers effect on the gas and humid barrier properties in PECVD deposited SiOx film on PET surface

Deep multilevel wet etching of fused silica glass microstructures in BOE solution

Stress-Etching Using Laser Electrochemical Micromachining with Masks

Experimental Study on Roughness and Flatness of Micromirror Fabricated by Different Anisotropic Silicon Etching Processes

Effective Approaches to Improve Au Etching Process Performance in MEMS Devices

Deep wet etching of borosilicate glass and fused silica with dehydrated AZ4330 and a Cr/Au mask

Wet Etching of Quartz Using a Solution Based on Organic Solvents and Anhydrous Hydrofluoric Acid

Molybdenum etching using an SF6, BCl3 and Ar based recipe for high aspect ratio MEMS device fabrication

A Two-step Wet Etching Process of PZT Thin Film With Ultra-low Undercut for MEMS Applications

KOH-based shallow etching for exposing subsurface damage and increasing laser damage resistance of fused silica optical surface

Deep Reactive Ion Etching of Z-Cut Alpha Quartz for MEMS Resonant Devices Fabrication

Ground-based Investigations of Atomic Oxygen Erosion Behaviors of Kapton and ZnO-siloxane Coatings on Kapton

Post Etch Residue Removal and Material Compatibility in BEOL Using Formulated Chemistries

Etching of Ga2O3: an important process for device manufacturing