Abstract:Plasma etching with high selectivity and anisotropy for 20 nm poly-Si gate patterning on EOT of 1.4 nm gate oxynitride is developed in a Cl2/HBr/O2 gas mixture successfully. Direct write e-beam lithography is used for an SAL601 chemically amplified negative resist pattern. Using a combination of resist ashing and TEOS hard mask trimming process, sub-25 nm TEOS SiO2 mask patterns are obtained in the control. Various gas mixtures based on Cl2, HBr, and O2 have been used to study the etching characteristics of poly-Si on EOT of 1.4 nm gate oxynitride. The O2 content as well as HBr are very sensitive to etch rate, selectivity, and the protection of the sidewalls of polysilicon, owing to SiO2-like film, SiOxBry, formed on the etched surface confirmed by x-ray photoelectron spectroscopy. And the ratio of Cl2/HBr/O2 in gas mixture is also tightly related to the etching profile. Using a four-step etching process under optimum conditions the selectivity of poly-Si to oxide is much higher than 500:1, in fact, after polysilicon etching the net deposition of oxide is observed, and no damage on the active area beside the gates for EOT of 1.4 nm gate oxide is observed, too. The etching profile of the 20 nm poly-Si gate pattern is perfectly vertical and an overall narrowing by an estimated 5 nm is observed for oxide masked poly-Si gate etching. The possible mechanism is discussed. This etching process combined with resist ashing and the TEOS hard mask trimming process are implemented successfully to the fabrication of high performance 36 nm gate length complementary metal–oxide–semiconductor (CMOS) devices and 42 nm gate length 32 frequency dividers with 57 stage/201 stage CMOS ring oscillators embedded, the EOT of gate oxynitrid is 1.4 nm, and very good results are obtained.

Investigation of Amorphous Silicon As Dry Etch Hard Mask in BEOL Low-k Dielectric Patterning

Optimization of Polysilicon Gate Etching Process in SONOS Memory Fabrication

Step Coverage and Dry Etching Process Improvement of Amorphous Carbon Hard Mask

Role of Oxygen in Amorphous Carbon Hard Mask Plasma Etching

Study on maskless etching of silicon symmetric beam-mass structure in aqueous KOH

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

A spin-on photosensitive polymeric etch protection mask for anisotropic wet etching of silicon

Maskless Etching Of Three-Dimensional Silicon Structures In Koh

Etch mechanism of an Al2O3 hard mask in the Bosch process

Nanometer Scale Pattern Replication Using Electron-Beam Direct Patterned Sio2 As the Etching Mask

Wet Scandium Etching for hard mask formation on a silicon substrate

The investigation of DARC etch back in DRAM capacitor oxide mask opening

Study of Selective Dry Etching Effects of 15-Cycle Si0.7Ge0.3/Si Multilayer Structure in Gate-All-Around Transistor Process

Low-temperature plasma etching of high aspect-ratio densely packed 15 to sub-10 nm silicon features derived from PS-PDMS block copolymer patterns

Toward Controllable Wet Etching of Monocrystalline Silicon: Roles of Mechanically Driven Defects

20 Nm Polysilicon Gate Patterning and Application in 36 Nm Complementary Metal–oxide–semiconductor Devices

Development of a facile block copolymer method for creating hard mask patterns integrated into semiconductor manufacturing

Rapid prototyping of etch test structures for hard mask development using electron beam lithography

Total Solutions for 40nm Metal Hard-Mask All-In-One Etch Process

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

Interface Optimization and Performance Enhancement of Er2O3-Based MOS Devices by ALD-Derived Al2O3 Passivation Layers and Annealing Treatment