Abstract:Kapton film is a polymeric material widely used on low-Earth-orbit (LEO) spacecraft surfaces. In the LEO environment, atomic oxygen (AO) is spaceflight materials' most destructive environmental factor. The erosion mechanism of AO on Kapton films has long been an important issue, where the parameter dependence of the AO effect has received increasing attention. Studies of AO energy and cumulative flux have been extensively carried out, while the influence mechanism of the incidence angle and flux density is not fully understood. The AO incidence angle and flux density in space are diverse, which may cause different damage effects on aerospace materials. In this paper, the dependence of the incidence angle and flux density in the damaging effect of AO on Kapton films was investigated using ground-based AO test technology and the reactive molecular dynamics (ReaxFF MD) simulation technique. Firstly, the ground-based experiment obtained the mass loss data of Kapton films under the action of AO with a variable incidence angle and flux density. Then, the mass loss, temperature rise, product, and erosion yield of Kapton during AO impact with different incidence angles and dose rates were calculated using the ReaxFF MD method. The influences of the incidence angle and flux density on the damage mechanism of the AO effect were discussed by comparing the simulation and test results. The results show that the AO effect in the lower incidence angle range (0-60°) is independent of the incidence angle and depends only on the amount of impacted atomic oxygen. AO in the higher incidence angle range (60-90°) has a surface stripping effect, which causes more significant mass loss and a temperature rise while stripping raised macromolecules from rough surfaces, and the erosion effect increases with the increasing incidence angle and amount of impacted atomic oxygen. There is a critical value for the influence of flux density on the AO effect. Above this critical value, AO has a reduced erosive capacity due to a lower chance of participating in the reaction. The amount of each main product from the AO effect varies with the incidence angle and flux density. Nonetheless, the total content of the main products is essentially constant, around 70%. This work will contribute to our understanding of the incidence angle and flux density dependence of the AO effect and provide valuable information for the development of standards for ground simulation tests.

Ground-based Investigations of Atomic Oxygen Erosion Behaviors of Kapton and ZnO-siloxane Coatings on Kapton

Ground-based investigations of atomic oxygen erosion behaviors of Al2O3 coating on kapton

Studies on the Erosion Mechanism of Kapton and Its Protective Effect

ATOMIC OXYGEN IRRADIATION INDUCED DEGRADATION OF POLYIMIDE WITHOUT AND WITH SILOXANE COATING

Ground-based Investigation of Atomic Oxygen Effects on Naked Ag and Ag with Protective Organic Coatings

Dependence of Incidence Angle and Flux Density in the Damage Effect of Atomic Oxygen on Kapton Film

Damage and degradation of mechanical properties of polyimide-based materials under atomic oxygen attack: A molecular dynamics simulation study

Effect of Coating Thickness on the Atomic Oxygen Resistance of Siloxane Coatings Synthesized by Plasma Polymerization Deposition Technique

Oxygen-atom erosion to Ag and TiO2-siloxane thermal control coatings on Ag surface

Atomic oxygen effects on polymers containing silicon or phosphorus: Mass loss, erosion yield, and surface morphology

ATOMIC OXYGEN EFFECTS ON NAKED Ag AND Ag WITH PROTECTIVE ORGANIC COATINGS

Atomic Oxygen Adaptability of Flexible Kapton/Al2O3 Composite Thin Films Prepared by Ion Exchange Method

Protection of Copper from Atomic Oxygen by Copper-Based Al2O3 Coatings

The Atomic Oxygen Erosion Resistance Effect and Mechanism of the Perhydropolysilazane-Derived SiOx Coating Used on Polymeric Materials in Space Environment

Reactive molecular dynamics simulation on the disintegration of Kapton and Upilex-S during atomic oxygen impact

Atomic oxygen resistance and tribological performance of a self-stratifying Polydimethylsiloxane-polyamide-imide/molybdenum disulfide lubricating coating

Property of Protection against Simultaneous Action between Atomic Oxygen Erosion and Ultraviolet Irradiation by MIL-53(Al) Coating

The Power Source Effect on SiOx Coating Deposition by Plasma Enhanced Chemical Vapor Deposition

Reactive molecular dynamics simulation on the disintegration of Kapton, POSS polyimide, amorphous silica, and teflon during atomic oxygen impact using the ReaxFF reactive force-field method

The effects of atomic oxygen and ion irradiation degradation on multi-polymers: A combined ground-based exposure and ReaxFF-MD simulation

Study on the protection of TiO2-K2SiO3 inorganic coatings for Ag used in space