Abstract:Oxidative etching possesses an enriched flexibility and atomic-level accuracy in tailoring the size, morphology, surface structure, and composition of colloidal nanocrystals toward their catalytic and sensing applications. In this work, we choose one-dimensional penta-twinned Pd nanorods as a model system and apply liquid cell transmission electron microscopy (LCTEM) to investigate the detailed nanoscale etching process under different solution environments, which are DI water/e-beam (weakly oxidative), sodium chloride (NaCl) solution/e-beam (moderately oxidative), and ferric chloride (FeCl3) solution/e-beam (strongly oxidative), respectively. Increasing the oxidative strength of solution alone accelerates the dissolution kinetics and drives the system from the (near)-equilibrium etching, where nanorods appear in flat and low-indexed ends (for DI water/e-beam) to nonequilibrium etching with slender tips formed as intermediate products (for FeCl3/e-beam). Under a nonequilibrium etching condition, both symmetric and asymmetric etching occurred, that is, the penta-twinned structure either retained (for symmetric etching) or dissolved to a fourfold-, threefold-, and twofold-twinned and single-crystalline structure (for asymmetric etching), depending on the structural defects-induced strain distribution. The formation of slender tips of different structures can be further understood via energetic analysis and strain relaxation. In particular, in situ LCTEM results were successfully reproduced by flask system-based etching experiments; hence, direct correlations were built between LCTEM and conventional colloidal etching reactions. This work comprehends the present understanding on the synergetic roles of structure characteristics and solution chemistry for the etching of multiply twinned nanoparticles toward their precise controlled synthesis and practical applications.

Effective Approaches to Improve Au Etching Process Performance in MEMS Devices

Synergy Between Structure Characteristics and the Solution Chemistry in a Near/Non-Equilibrium Oxidative Etching of Penta-Twinned Palladium Nanorods

Stress-Etching Using Laser Electrochemical Micromachining with Masks

A Two-step Wet Etching Process of PZT Thin Film With Ultra-low Undercut for MEMS Applications

Step Coverage and Dry Etching Process Improvement of Amorphous Carbon Hard Mask

Optimization of approach for metal contamination reduction

CMOS-Compatible Electrochemical Nanoimprint:High Throughput Fabrication of Ordered Microstructures on Semiconductor Wafer by Using a Glassy Carbon Mold

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

A study of post-etch wet clean on electrical and reliability performance of Cu/low k interconnections

Influence of Etchants on Etched Surfaces of High-Strength and High-Conductivity Cu Alloy of Different Processing States

Uniform Metal-Assisted Chemical Etching for Ultra-High-Aspect-Ratio Microstructures on Silicon

Chemical Etching Processes at the Dynamic GaAs/Electrolyte Interface in the Electrochemical Direct-Writing Micromachining

Toward Controllable Wet Etching of Monocrystalline Silicon: Roles of Mechanically Driven Defects

Effect of Isopropanol on Gold Assisted Chemical Etching of Silicon Microstructures

Deep Reactive Ion Etching of Z-Cut Alpha Quartz for MEMS Resonant Devices Fabrication

Total Solutions for 40nm Metal Hard-Mask All-In-One Etch Process

Metal Ions' Dynamic Effect on Metal-Assisted Catalyzed Etching of Silicon in Acid Solution

(Digital Presentation) Uniformity and Profile Improvement of Fin Etching Process at Wafer Extreme Edge for Finfet Mass Production

Design and Application of a Metal Wet-Etching Post-Process for the Improvement of CMOS-MEMS Capacitive Sensors

Metal corrosion and passivation swelling defect study of ultra low pattern density thick metal etch process

Oxide Or Metal Interface Damage Improvement Of Deep Silicon Etch Process By Low Power Rf Of Low Frequency