Abstract:Heterogeneous 3D integration is being hailed as the driver for new technologies due to its stacked device architecture. This increases functionality as the number and length of interconnecting wires decreases, in turn decreasing power consumption. In these advanced packaging technologies, the metal redistribution layers (RDLs) and the insulating polymer surrounding them are crucial components on which stringent reliability requirements are placed. The metal RDL’s are necessary to reroute signals from device level to packaging level. The polymer insulator, used as an alternative to traditional dielectric materials, must (i) be photosensitive to be compatible with lithography processing steps, (ii) possess high mechanical strength, (iii) exhibit good electrical performance, (iv) have a high thermal stability and glass transition temperature, and crucially (v) it must not be hygroscopic. Low or no moisture uptake of the polymer is essential as any moisture can cause mechanical and electrical reliability issues. Absorbed moisture can cause oxidation of Cu lines leading to the well-known problem of Cu diffusion resulting in voids, contact issues, delamination, electromigration and higher leakage currents. Area selective deposition (ASD) could greatly benefit these RDL’s by preferentially depositing an oxygen barrier to stop the oxidation of the Cu lines. The proprietary polymer used in this work is part of the WPR series by JSR Corporation and is a thermosetting phenol-based polymer which displays a high mechanical stability as it contains rubber nanoparticles, 70 nm in diameter. These are added to the polymer to increase the toughness and to prevent cracks and fractures forming and propagating through the film. However, achieving ASD with this polymer is difficult as the polymer is designed to have good adhesion properties so it will easily adhere to the Cu in the metal lines, and there are two materials of interest to passivate, the polymer itself and the rubber nanoparticles. In this work the surface is passivated by utilizing a polymerizing octafluorocyclobutane (C 4 F 8 ) plasma which creates a Teflon-like film on the surface. The surface morphology and hydrophobicity are investigated to assess the best plasma exposure time, which was found to be 30 s. Surface chemistry from XPS analysis reveals surface modification through the deposition of fluorine rich groups from the 30 s C 4 F 8 plasma exposure, Figure 1(a). Water contact angle measurements reveal an initial hydrophobic surface (~94°) but this hydrophobicity decreases over the course of several seconds. Following the 30 s C 4 F 8 plasma exposure, the hydrophobicity increases significantly to above 110° and remains stable as shown in Figure 1(b). Surface morphology studies carried out by AFM demonstrates no increase in surface roughness following plasma exposure, Figure 1(c) and (d). ALD tests show the process to be selective to the tetrachloride family of ALD precursors. No selectivity was observed with tetrakis (dimethylamino) or isopropoxide based precursors. This process has the capability to block approximately 2 nm of TiO 2 and HfO 2 from these tetrachloride precursors. Studies of the same process on Cu substrates show that the metal surface is only temporarily modified, and ALD growth can still take place. Reliability stress and corrosion tests were performed to assess if the selectively deposited barriers could prevent Cu oxidation. Figure 1(a) C 1s XPS spectra showing difference before and after plasma treatment, (b) WCA value increases following plasma treatment, and AFM images in (c) and (d) show no change in the surface following plasma exposure. Figure 1

Post Etch Residue Removal and Material Compatibility in BEOL Using Formulated Chemistries

Barrier And Low K Polish With A Novel Alkaline Barrier Slurry Combining With Fa/O Chelating Agent

Plasma Induced Damage Reduction of Ultra Low-k Dielectric by Using Source Pulsed Plasma Etching for Next BEOL Interconnect Manufacturing

Industrial Challenges of TiN Hard Mask Wet Removal Process for 14nm Technology Node

High Throughput Wet Etch Solution for BEOL TiN Removal

Post Cleaning for FEOL CMP with Silica and Ceria Slurries

Effect of in-line electron beam treatment on the electrical performance of Cu/organic low-k damascene interconnects

Integration of Al2O3 Etch Stop Layer in 21nm Pitch Dual-Damascene BEOL interconnects

Surface Passivation of Polymer Based Redistribution Layers for Area Selective Deposition of an Oxygen Barrier

Total Solutions for 40nm Metal Hard-Mask All-In-One Etch Process

A 90nm dual damascene hybrid (organic/inorganic) low-k - Copper BEOL integration scheme

Contact Vs. Non-Contact Cleaning: Correlating Interfacial Reaction Mechanisms to Processing Methodologies for Enhanced FEOL/BEOL Post-CMP Cleaning

The Effect of Delay Between Dry Etch and Wet Clean Processing Steps on Cleaning of Post-Etch Residues

Polyimide-Damage-Free, CMOS-Compatible Removal of Polymer Residues from Deep Reactive Ion Etching Passivation

SF₆ Optimized O₂ Plasma Etching of Parylene C.

SF6 Optimized O2 Plasma Etching of Parylene C

Effect of Structure to Promote Organic Residue Removal during Cu Post-Chemical Mechanical Planarization (p-CMP) Cleaning

A study of post-etch wet clean on electrical and reliability performance of Cu/low k interconnections

A spin-on photosensitive polymeric etch protection mask for anisotropic wet etching of silicon

The Role of Dipotassium Ethylenediaminetetraacetic Acid and Potassium Oleate on Chemical Mechanical Planarization Relevant to Heterogeneous Materials of Cobalt Interconnects

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement