Abstract:Zirconium carbide (ZrC) ceramics is an important candidate material for structural applications both at high temperature and intensive irradiation. However, its sensitivity to defects and cracks often causes low reliability and limited the application of ZrC ceramics. In this work, graphite nanoplatelets (GNPs) doped zirconium carbide ceramics were prepared by spark plasma sintering (SPS). The results show that the addition of GNPs not only improved the densification of ZrC ceramics but also inhibited grain growth of ZrC matrix phase. The GNPs were mainly located at the grain boundaries, and the c-axis of the disk-like GNPs preferred to align with the applied pressing direction during SPS. The preferred orientation of GNPs in the sintered ceramics resulted in anisotropic microstructure and fracture toughness of the material. Compared with the monolithic ZrC ceramics with a fracture toughness of 2.27 MPa m1/2, GNPs doped ceramics shows higher fracture toughness. The fracture toughness of ZrC ceramics with 0.5, 1.5, 3 vol% GNPs are 2.70 MPa m1/2, 3.03 MPa m1/2 and 3.24 MPa m1/2 measured on the surface perpendicular to the applied pressing direction and 3.43 MPa m1/2, 3.66 MPa m1/2 and 4.55 MPa m1/2 measured on the surface parallel to the applied pressing direction, respectively. The crack deflection and re-initiation by GNPs are the main toughening mechanisms for the GNPs doped ZrC ceramics.

Zirconia-based Nanocomposite Toughened by Functionalized Multi-Wall Carbon Nanotubes

Toughening effect of multiwall carbon nanotubes on 3Y-TZP zirconia ceramics at cryogenic temperatures

Study on toughening effect of zirconia nanocomposites

A Novel Processing Route to Develop Alumina Matrix Nanocompositesreinforced with Multi-Walled Carbon Nanotubes

Mechanical and Electrical Properties of Chemically Modified MWCNTs/3Y-TZP Composites

Fracture Toughness And Toughening Mechanisms In A (Zrb2-Sic) Composite Reinforced With Boron Nitride Nanotubes And Boron Nitride Nanoplatelets

ZrB2-CNTs Nanocomposites Fabricated by Spark Plasma Sintering

Enhanced Toughness of KZr2(PO4)3 Ceramics Via Hydrothermal Incorporation of Multi-Walled Carbon Nanotubes

The effects of multiwalled carbon nanotubes on the hot-pressed 3 mol% yttria stabilized zirconia ceramics

Chemical Vapor Deposition Synthesis Carbon Nanosheet–Coated Zirconium Diboride Particles for Improved Fracture Toughness

Toughening of Ti3SiC2 with 3Y-TZP addition by spark plasma sintering

Failure investigation of carbon nanotube/3Y-TZP nanocomposites

Influence of the Microstructure Evolution of ZrO2 Fiber on the Fracture Toughness of ZrB2–SiC Nanocomposite Ceramics

Technologies and properties investigations of CNTs reinforced 3Y-ZrO2 ceramics with hot-pressing sintering

Graphite nanoplatelets toughened zirconium carbide ceramics prepared by spark plasma sintering

Preparation and Electrical Characterization of Carbon Nanotube /zro2composite Ceramics

Synthesis of zirconia nanoparticles on carbon nanotubes and their potential for enhancing the fracture toughness of alumina ceramics

Tensile Behavior of Hybrid Tungsten Composites with Zirconium Carbide Nanoparticles and Tungsten Fibers

Microstructural Evolution and Mechanical Properties of Carbon Nanotubes–reinforced TZM Composites Synthesized by Powder Metallurgy

Enhanced Toughness Of Zirconia Ceramics With Graphene Platelets Consolidated By Spark Plasma Sintering

Effects of the addition of multi-walled carbon nanotubes on the microstructure and properties of Ti(C,N)-based cermets prepared by spark plasma sintering