Abstract:Zirconium carbide (ZrC) ceramics is an important candidate material for structural applications both at high temperature and intensive irradiation. However, its sensitivity to defects and cracks often causes low reliability and limited the application of ZrC ceramics. In this work, graphite nanoplatelets (GNPs) doped zirconium carbide ceramics were prepared by spark plasma sintering (SPS). The results show that the addition of GNPs not only improved the densification of ZrC ceramics but also inhibited grain growth of ZrC matrix phase. The GNPs were mainly located at the grain boundaries, and the c-axis of the disk-like GNPs preferred to align with the applied pressing direction during SPS. The preferred orientation of GNPs in the sintered ceramics resulted in anisotropic microstructure and fracture toughness of the material. Compared with the monolithic ZrC ceramics with a fracture toughness of 2.27 MPa m1/2, GNPs doped ceramics shows higher fracture toughness. The fracture toughness of ZrC ceramics with 0.5, 1.5, 3 vol% GNPs are 2.70 MPa m1/2, 3.03 MPa m1/2 and 3.24 MPa m1/2 measured on the surface perpendicular to the applied pressing direction and 3.43 MPa m1/2, 3.66 MPa m1/2 and 4.55 MPa m1/2 measured on the surface parallel to the applied pressing direction, respectively. The crack deflection and re-initiation by GNPs are the main toughening mechanisms for the GNPs doped ZrC ceramics.

Toughening effect of multiwall carbon nanotubes on 3Y-TZP zirconia ceramics at cryogenic temperatures

Zirconia-based Nanocomposite Toughened by Functionalized Multi-Wall Carbon Nanotubes

Toughening Mechanisms of ZTA Ceramics at Cryogenic Temperature (77 K)

Fracture Toughness of 3 Mol% Yttria-Stabilized Zirconia at Cryogenic Temperatures

R‐Curve Behavior of 3Y‐TZP at Cryogenic Temperatures

Effect of Y2O3 Contents and Grain Sizes on the Mechanical Properties and Transformation of Zirconia Ceramics at Cryogenic Temperatures

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Slow Crack Growth Behavior of 3Y-TZP in Cryogenic Environment Using Dynamic Fatigue and Indentation Technique

The effects of multiwalled carbon nanotubes on the hot-pressed 3 mol% yttria stabilized zirconia ceramics

Phase Transformation and Exceptional Mechanical Properties of 3Y-TZP at Cryogenic Temperature

Effect of Multiwall Carbon Nanotubes on Electrical and Dielectric Properties of Yttria‐Stabilized Zirconia Ceramic

Critical grain size and fracture toughness of 2 mol.% yttria-stabilized zirconia at ambient and cryogenic temperatures

High temperature deformation mechanisms in monolithic 3YTZP and 3YTZP containing single wall carbon nanotubes

Toughening of Ti3SiC2 with 3Y-TZP addition by spark plasma sintering

Preparation And High-Temperature Strengthening Of Tetragonal Zirconia Mullite Whisker Composites

Effects of zirconium source and content on zirconia crystal form, microstructure and mechanical properties of ZTM ceramics

Mechanical and Electrical Properties of Chemically Modified MWCNTs/3Y-TZP Composites

Mechanical and thermal properties of Al 2O 3-ZrO 2 composite ceramics at cryogenic temperatures

Technologies and properties investigations of CNTs reinforced 3Y-ZrO2 ceramics with hot-pressing sintering

Effects of the addition of multi-walled carbon nanotubes on the microstructure and properties of Ti(C,N)-based cermets prepared by spark plasma sintering

Graphite nanoplatelets toughened zirconium carbide ceramics prepared by spark plasma sintering