Abstract:Objectives To investigate transient thermal stresses that developed in 3Y-TZP green compacts during speed sintering. Methods A total of 312 disc-shaped green compacts (Ø17.1 ×1, 1.5, 2, 2.5, 3 mm) were cold-isostatically pressed from 3Y-TZP powder (Zpex, Tosoh Corp.) for speed sintering studies as well as compositional analysis and biaxial flexural strength measurements (both at room temperature and following heating at 90 °C/min to 500 °C). Flexural strength was determined using the piston-on-3-ball method. Phase assemblies were analyzed using the X-ray diffraction method. Effects of heating/cooling rates on transient stresses were investigated by conducting definitive sintering studies to determine the threshold for fracture. Finite element analysis (FEA) was used to validate the experimental findings using measured thermomechanical properties. Results The bulk and relative density of the green compact were 2.95 ± 0.03 g/cm 3 and 48.52% ± 0.45%. The flexural strength was drastically decreased from 10.3 ± 0.4 MPa to 1.09 ± 0.07 MPa following heating at 90 °C/min to 500 °C. The monoclinic and tetragonal contents were 54.9% and 45.1%, respectively. The threshold for fracture was located at 500 °C during the first heating stage with a 90 °C/min heating rate in specimens of 2.5 mm thickness or greater. No fractures occurred in the second heating stage and cooling phase. The FEA estimated that the principal transient tensile stress was ∼1.14 MPa at 500 °C during the heating phase, which exceeded the corresponding flexural strength (1.09 ± 0.07 MPa). Significance Advanced FEA methods are an accurate and efficient tool to analyze the history of transient stresses during sintering of ceramic dental restorations.

Fracture Toughness of 3 Mol% Yttria-Stabilized Zirconia at Cryogenic Temperatures

R‐Curve Behavior of 3Y‐TZP at Cryogenic Temperatures

Critical grain size and fracture toughness of 2 mol.% yttria-stabilized zirconia at ambient and cryogenic temperatures

Effect of Y2O3 Contents and Grain Sizes on the Mechanical Properties and Transformation of Zirconia Ceramics at Cryogenic Temperatures

Slow Crack Growth Behavior of 3Y-TZP in Cryogenic Environment Using Dynamic Fatigue and Indentation Technique

Toughening effect of multiwall carbon nanotubes on 3Y-TZP zirconia ceramics at cryogenic temperatures

Phase Transformation and Exceptional Mechanical Properties of 3Y-TZP at Cryogenic Temperature

[Study on Low Temperature Degradation of Dental Zirconia Ceramic].

Toughening Mechanisms of ZTA Ceramics at Cryogenic Temperature (77 K)

Fracture Toughness of Aluminum Nitride Ceramics at Cryogenic Temperatures

Mechanical and thermal properties of Al 2O 3-ZrO 2 composite ceramics at cryogenic temperatures

Enhanced fracture toughness of silicon nitride ceramics at cryogenic temperatures

How Does Phase Transformation Affect the Fatigue Behavior of 3Y-TZP in Cryogenic Environment?

Fracture mechanism of a fracture-resistant CNT/alumina nanocomposite at cryogenic temperature

Si3N4-SiCw composites as structural materials for cryogenic application

High Temperature Fracture Toughness and Residual Stress in Thermal Barrier Coatings Evaluated by an In-Situ Indentation Method

Fracture mode and compressive strength of ice-templated porous zirconia

Toughening Ceramics down to Cryogenic Temperatures by Reentrant Strain-Glass Transition

Transient thermal stresses developed during speed sintering of 3 mol% yttria-stabilized tetragonal zirconia polycrystals

High Temperature Mechanical Properties of Zirconia Metastable T '-Phase Degraded Yttria Stabilized Zirconia

Mechanical Properties Durability of Sc2O3-Y2O3 Co-Stabilized ZrO2 Thermal Barrier Materials for High Temperature Application