Abstract:The fatigue behavior of as-cast Mg–12%Zn–1.2%Y–0.4%Zr alloy has been investigated. The S–N curve showed that the fatigue strength at 107 cycles was 45MPa. Scanning electron microscopy observations on the surfaces of the failed and unfailed specimens (after up to 1×107 cycles) suggested that the slip bands could act as preferential sites for non-propagating fatigue crack initiation, and the I-phase could effectively retard fatigue crack propagation (FCP). The macro fracture morphology clearly indicated that the overall fracture surface was composed of three regions, i.e. a fatigue crack initiation region (Region 1), a steady crack propagation region (Region 2) and a tearing region (Region 3). High-magnification fractographs showed that only porosities can act as the crack initiation sites for all specimens. Moreover, for specimens with fatigue lifetimes lower than 2×105 cycles, the cracks mostly initiated at the subsurface or surface of the specimen. However, when the fatigue lifetime was equal to or higher than 2×105 cycles, the fatigue crack initiation sites transferred to the interior of the specimen. The maximum stress intensity factors corresponding to the transition sites between Regions 1, 2 and 3 were 2 and 4.2MPam1/2, respectively. When the maximum stress intensity factor Kmax was lower than 4.2MPam1/2, in the steady crack propagation region, due to the retarding effect of I-phase/α-Mg matrix interfaces, the fatigue cracks tended to pass the I-phase/α-Mg matrix eutectic pockets directly and propagated through the grain cells, resulting in the formation of many flat facets on the fracture surface. However, when the maximum stress intensity factor was higher than 4.2MPam1/2, in the sudden failure region, the rigid bonding of I-phase/α-Mg matrix interfaces was destroyed and the cracks preferentially propagated along the interfaces, which resulted in the fracture surface being almost completely composed of cracked I-phase/α-Mg matrix eutectic pockets. Based on microstructural observation and the fracture characteristics of the two regions, it is suggested that with an increase in crack tip driving force, the FCP mode changes from transgranular propagation to intergranular propagation.

How Does Phase Transformation Affect the Fatigue Behavior of 3Y-TZP in Cryogenic Environment?

Slow Crack Growth Behavior of 3Y-TZP in Cryogenic Environment Using Dynamic Fatigue and Indentation Technique

Phase Transformation and Exceptional Mechanical Properties of 3Y-TZP at Cryogenic Temperature

R‐Curve Behavior of 3Y‐TZP at Cryogenic Temperatures

Fracture Toughness of 3 Mol% Yttria-Stabilized Zirconia at Cryogenic Temperatures

Effect of Y2O3 Contents and Grain Sizes on the Mechanical Properties and Transformation of Zirconia Ceramics at Cryogenic Temperatures

Study of the Fracture Behavior of Tetragonal Zirconia Polycrystal with a Modified Phase Field Model

Transformation and Fracture of Zro2-Based Ceramics at Low-Temperatures

Cryogenic Investigations into the Effect of Impact-Oscillatory Loading on Changes in the Mechanical Properties and Structural Condition of VT23M Two-Phase Titanium Alloy

Physical Mechanism of Nanocrystalline Composite Deformation Responsible for Fracture Plastic Nature at Cryogenic Temperatures

High Temperature Mechanical Properties of Zirconia Metastable T '-Phase Degraded Yttria Stabilized Zirconia

Fatigue-Induced HCP-to-FCC Phase Transformation Resulting in Two FCC-Zr Variants in Pure Zirconium

Effects of cryogenic treatments on phase transformations, microstructure and mechanical properties of near βTi alloy

Effects of triaxial stress on martensite transformation, stress–strain and failure behavior in front of crack tips in shape memory alloy NiTi

Toughening effect of multiwall carbon nanotubes on 3Y-TZP zirconia ceramics at cryogenic temperatures

A thermodynamically-consistent non-isothermal phase-field model for probing evolution of crack propagation and phase transformation

Phase Transformation and Slow Crack Growth Study of Y-TZP Dental Ceramic

The Fatigue Behavior of I-phase Containing As-Cast Mg–Zn–Y–Zr Alloy

Structural evolution of a CuZr-based bulk metallic glass composite during cryogenic treatment observed by in-situ high-energy X-ray diffraction

Fatigue and fracture behavior of an aluminum-lithium alloy 8090-T6 at ambient and cryogenic temperature

Interfacial Endogenous Stress-Induced Phase-Stress Partition in Tin-Lead Dual-Phase Alloy at Cryogenic Temperature