Abstract:In the ultra-large-scale integration (ULSI) technologies, polysilicon resistors are usually employed in the integrated circuits as a precise analog resistor element for a variety of applications, such as DAC (digital resistor give the solution of the linearity and Rs concerns to analog converter) in analogue circuits [1-3]. Conventionally the polysilicon resistance can be adjusted by ion implantation and post annealing process [4]. For the self-aligned implantation process, the dosage changes which are always utilized to adjust the resistance are feasible to induce the MOS characteristics changes, especially in the submicron process whose short-channel effects (SCE) are much more sensitive to the dosages [5]. In this work, we propose a new inner anneal process in N2ambient after polysilicon re-oxidation to reduce the polysilicon resistance by changing the polysilicon grain size. The test patterns are manufactured on 300mm-diameter wafer by 65-nm 1-poly 7-metal standard CMOS technology. After polysilicon re-oxidation to form oxide film on polysilicon surface, the wafers are annealed at 800oC, 900oC, 950oC and 1000oC in N2ambient, respectively. Fig. 1 shows the process flow and annealing process steps in the flow. After anneal, the polysilicon grain size is measured by X-ray powder diffraction (XRD). And the electric characteristics for NMOS, PMOS and polysilicon resistance are tested. Fig. 2 shows the poly resistance reduction proportion and poly grain size after anneal at 800oC, 900oC, and 1000oC for 5min, and 950oC for 20min in N2 ambient, respectively. Only after annealing at 950oC or above for 5min, the resistance can be obviously reduced, due to the poly grain size increasing. Fig. 3 shows threshold voltages (Vt) variation proportions of NMOS and PMOS owning gate length of 65nm and width 0.12µm after utilizing annealing process at different temperatures. PMOS is more sensitive to the anneal process than NMOS. But after anneal at 950oC or below, the threshold variation for both NMOS and PMOS is less than 5%, which is acceptable for the integration process manufacturing. A new anneal process at N2 ambient to adjust the polysilicon resistance has been proposed. It has been verified that utilizing anneal process at 950oC or below, the 65nm MOS performances can be maintained almost same as before. Consequently, it is considered that the anneal method can be to be applied to the deep submicron integration process. References [1] C. D. Parikh, and R. M. Patrikar, Solid-state Electronics, 43, 683 (1999). [2] R. Murii, and M. J. Deen,, IEEE Trans. Electron Devices, 49, 187 (2002). [3] C. Uang, H. Chuang, S. Tsai, K. Thei, P. Lai, S. Fu, Y. Tsai, W. Liu, IWJT, 293 (2004). [4] S. Gupta, J. Electrochem. Soc. 149, G271 (2002). [5] R. H. Dennard, F. J. Gasensslen, H. M. Yu, V. L. Rideout, E. Bassous, A. R. Leblanc, Solid-state Circuits Soc Mag. IEEE, 87, 668 (1999). Figure 1

Exploration of High‐Pressure Annealing and Microwave Annealing in Palladium Germano‐Silicide Formation for Si0.8Ge0.2‐Based Complementary Metal‐Oxide–Semiconductor Transistors

Ni Silicide and Ni Germanosilicide Self-Aligned Process for 65nm and Beyond CMOS Technology by 2-Step Rapid Thermal Annealing

Influence of High Pressure Annealing on Electrical Properties of Surface Layer of Neutron Irradiated or Germanium-Doped Czochralski-Grown Silicon

Effect of High Pressure Annealing on Electrical Properties of Nitrogen and Germanium Doped Silicon

Low-temperature Annealing of Polycrystalline Si/sub 1-X/ge/sub X/ after Dopant Implantation

Revealing the Defects Introduced in N- or Ge-doped Cz-Si by Γirradiation and High Temperature-High Pressure Treatment

Micro-characterisation of Si wafers by high-pressure thermopower technique

Effect of Post-Metal Annealing on the Quality of Thermally Grown Silicon Dioxide on 6H- and 4H-Sic

Variations of High-Pressure Thermoelectric and Mechanical Properties of Si Single Crystals under Doping with N and P–T Pre-Treatment

Germanium Doping of Si Substrates for Improved Device Characteristics and Yield

Microwave Effects on Metal–Semiconductor Contact of Heavily Nitrogen-Implanted Silicon

Characterization of Ni(Si,Ge) Films on Epitaxial SiGe(100) Formed by Microwave Annealing

Reliability Improvement of Ge Pmosfets with Al2O3 Dielectric by Ozone Post Annealing

Design on Formation of Nickel Silicide by a Low‐Temperature Pulsed Laser Annealing Method to Reduce Contact Resistance for CMOS Inverter and 6T‐SRAM on a Wafer‐Scale Flexible Substrate

Thermal Method to Reduce the Polysilicon Resistance for Deep Submicron Integration Process

Investigation of Ultrathin Ni Germanosilicide for Advanced pMOS Contact Metallization

Searching for Device Processing Compatible Ohmic Contacts to Implanted P-Type 4H-Sic

The material characterization of nickel germanosilicides on SiGe/Si substrate and the contact size effect on Schottky diodes

Pt interlayer effects on Ni germanosilicide formation and contact properties

Study of Interface State Density and Effective Oxide Charge in Post-Metallization Annealed SiO/sub 2/-Sic Structures

Low-temperature epitaxial SiGe:P for gate-all-around n-channel metal-oxide-semiconductor devices