Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Large-Area Si Solar Cells Based on Molybdenum Oxide Hole Selective Contacts

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Heterojunction solar cells with asymmetrically carrier-selective contact structure of molybdenum-oxide/silicon/magnesium-oxide

Amorphous oxygen-rich molybdenum oxysulfide Decorated p-type silicon microwire Arrays for efficient photoelectrochemical water reduction

Silicon solar cell with tunneling oxide on sulfur‐deficient intrinsic MoS2 thin film

MoOx Hole Collection Layer for A-Si: H Based Photovoltaic Cells

Large‐area MoOx/c‐Si heterojunction solar cells with a ICO/Ag back reflector

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Tunable work function of molybdenum oxynitride for electron-selective contact in crystalline silicon solar cells

< 50-μm thin crystalline silicon heterojunction solar cells with dopant-free carrier-selective contacts

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Simulation of High Efficiency Silicon Heterojunction Solar Cells with Molybdenum Oxide Carrier Selective Layer

Performance analysis of c-Si heterojunction solar cell with passivated transition metal oxides carrier-selective contacts

Tunable Hole Selective Transport by Solution‐processed MoO3‐x Via Doping for p‐Type Crystalline Silicon Solar Cells

Greatly enhanced hole collection of MoOx with top sub-10 nm thick silver films for gridless and flexible crystalline silicon heterojunction solar cells

Molybdenum oxide hole selective transport layer by hot wire oxidation-sublimation deposition for silicon heterojunction solar cells

In situ growth MoS 2 quantum dots as promising interface materials for silicon solar cells

Crystalline Silicon Heterojunction Solar Cells with Metal Oxide Window Layers

Atomic-Layer-Deposited H:MoO x Function Layer as Efficient Hole Selective Passivating Contact in Silicon Solar Cells

Highly Efficient and Highly Flexible Thin Crystalline Silicon Heterojunction Solar Cells Based on Dopant-Free Carrier-Selective Contacts Fabricated with Simple Processes

Electrical characterization and defect states analysis of Ag/ITO/MoOx/n-Si/LiFx/Al carrier selective contact solar cells processed at room-temperature