Abstract:Full-area passivating contacts based on SiOx/poly-Si stacks are key for the new generation of industrial silicon solar cells substituting the passivated emitter and rear cell (PERC) technology. Demonstrating a potential efficiency increase of 1 to 2% compared to PERC, the utilization of n-type wafers with an n-type contact at the back and a p-type diffused boron emitter has become the industry standard in 2024. In this work, variations of this technology are explored, considering p-type passivating contacts on p-type Si wafers formed via a rapid thermal processing (RTP) step. These contacts could be useful in conjunction with n-type contacts for realizing solar cells with passivating contacts on both sides. Here, a particular focus is set on investigating the influence of the applied thermal treatment on the interfacial silicon oxide (SiOx) layer. Thin SiOx layers formed via ultraviolet (UV)-O3 exposure are compared with layers obtained through a plasma treatment with nitrous oxide (N2O). This process is performed in the same plasma enhanced chemical vapor deposition (PECVD) chamber used to grow the Si-based passivating layer, resulting in a streamlined process flow. For both oxide types, the influence of the RTP thermal budget on passivation quality and contact resistivity is investigated. Whereas the UV-O3 oxide shows a pronounced degradation when using high thermal budget annealing (T > 860 °C), the N2O-plasma oxide exhibits instead an excellent passivation quality under these conditions. Simultaneously, the contact resistivity achieved with the N2O-plasma oxide layer is comparable to that yielded by UV-O3-grown oxides. To unravel the mechanisms behind the improved performance obtained with the N2O-plasma oxide at high thermal budget, characterization by high-resolution (scanning) transmission electron microscopy (HR-(S)TEM), X-ray reflectometry (XRR) and X-ray photoelectron spectroscopy (XPS) is conducted on layer stacks featuring both N2O and UV-O3 oxides after RTP. A breakup of the UV-O3 oxide at high thermal budget is observed, whereas the N2O oxide is found to maintain its structural integrity along the interface. Furthermore, chemical analysis reveals that the N2O oxide is richer in oxygen and contains a higher amount of nitrogen compared to the UV-O3 oxide. These distinguishing characteristics can be directly linked to the enhanced stability exhibited by the N2O oxide under higher annealing temperatures and extended dwell times.

Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells

Oxide-nitride nanolayer stacks for enhanced passivation of p-type surfaces in silicon solar cells

The Passivation Characteristics of Poly-Si/SiOx Stack for High-Efficiency Silicon Solar Cells

Improved Surface Passivation of Rear SiN X /alo X Stacks in P‐type Boron‐Doped Czochralski Silicon Wafers During Dark Annealing at Elevated Temperatures

Improved Surface Passivation of Rear SiN x /AlO x Stacks in p-Type Boron-Doped Czochralski Silicon Wafers During Dark Annealing at Elevated Temperatures

Impact of interstitial oxygen trapped in silicon during plasma growth of silicon oxy-nitride films for silicon solar cell passivation

Development and Characterization of N2O-Plasma Oxide Layers for High-Temperature p-Type Passivating Contacts in Silicon Solar Cells

Long-term stability study of the passivation quality of polysilicon-based passivation layers for silicon solar cells

Impact of Boron Doping Concentration on Tunnel Oxide Passivated Contact in Front Surface for N-Type Poly-Si Based Passivated Contact Bifacial Solar Cells

Impact of Post-deposition Plasma Treatment on Surface Passivation Quality of Silicon Nitride Films

A Deep-Level Transient Spectroscopy Study of Gamma-Ray Irradiation on the Passivation Properties of Silicon Nitride Layer on Silicon

Regionalizing Nitrogen Doping of Polysilicon Films Enabling High‐Efficiency Tunnel Oxide Passivating Contact Silicon Solar Cells

n-Type polysilicon passivating contact for industrial bifacial n-type solar cells

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells

Three-Step Process for Efficient Solar Cells with Boron-Doped Passivated Contacts

Study on the Passivation of Si Surface by Incorporation of Nitrogen in Al 2 O 3 Thin Films Grown by Atomic Layer Deposition

Passivating Contact with Phosphorus‐Doped Polycrystalline Silicon‐Nitride with an Excellent Implied Open‐Circuit Voltage of 745 mV and Its Application in 23.88% Efficiency TOPCon Solar Cells

PASSIVATION EFFECT OF SiNx: H FILM ON CRYSTALLINE SILICON MATERIALS AND SOLAR CELLS

Microstructure and Photoelectric Properties of P-Doped Silicon-Rich Sinx Film As an N-Type Layer for Pin-Type Amorphous Silicon Thin Film Solar Cells

Enhancement of Electrical Properties of Nanostructured Polysilicon Layers Through Hydrogen Passivation

Fully screen-printed bifacial large area 22.6% N-type Si solar cell with lightly doped ion-implanted boron emitter and tunnel oxide passivated rear contact