Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Passivating Contact with Phosphorus‐Doped Polycrystalline Silicon‐Nitride with an Excellent Implied Open‐Circuit Voltage of 745 mV and Its Application in 23.88% Efficiency TOPCon Solar Cells

Regionalizing Nitrogen Doping of Polysilicon Films Enabling High‐Efficiency Tunnel Oxide Passivating Contact Silicon Solar Cells

A silicon oxide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 23%

Highly transparent oxygen‐doped poly‐Si with in‐situ N2O oxidant for poly‐Si passivating contacts in perovskite/silicon tandem solar cells

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells

Large-area bifacial n-TOPCon solar cells with in situ phosphorus-doped LPCVD poly-Si passivating contacts

High-efficiency n-TOPCon bifacial solar cells with selective poly-Si based passivating contacts

Application of n‐Polysilicon Rear Emitter for High‐Efficiency p‐TOPCon Solar Cells

Optimizing Phosphorus-Doped Polysilicon in TOPCon Structures Using Silicon Oxide Layers to Improve Silicon Solar Cell Performance

Enhancing poly-Si contact through a highly conductive and ultra-thin TiN layer for high-efficiency passivating contact silicon solar cells

Blistering-free carbon-doped polysilicon (n+) passivating contact with high surface passivation properties prepared by industrial tube PECVD

Application of dual-layer polysilicon deposited by PECVD in n -type TOPCon solar cells

Highly improved passivation of PECVD p-type TOPCon by suppressing plasma-oxidation ion-bombardment-induced damages

Screen-printed n-type industry solar cells with tunnel oxide passivated contact doped by phosphorus diffusion

Plasma Treatment for Chemical SiOx Enables Excellent Passivation of P-Type Polysilicon Passivating Contact Featuring the Lowest J0 Of-6 Fa/cm2

Numerical Simulation and Experiment of a High-Efficiency Tunnel Oxide Passivated Contact (TOPCon) Solar Cell Using a Crystalline Nanostructured Silicon-Based Layer

Optimization of In-situ and Ex-situ doped p+ Passivating Contact for High Efficiency p-TOPCon Solar Cell Application

Optimization of activated phosphorus concentration in recrystallized polysilicon layers for the n-TOPCon solar cell application

Plasma treatment for chemical SiOx enables excellent passivation of p-type polysilicon passivating contact featuring the lowest J of ∼6 fA/cm2

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells