Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Fully screen-printed bifacial large area 22.6% N-type Si solar cell with lightly doped ion-implanted boron emitter and tunnel oxide passivated rear contact

n-Type polysilicon passivating contact for industrial bifacial n-type solar cells

Thin Al2O3 passivated boron emitter of n-type bifacial c-Si solar cells with industrial process

Approaching 23% with large‐area monoPoly cells using screen‐printed and fired rear passivating contacts fabricated by inline PECVD

High efficiency large area n‐type front junction silicon solar cells with boron emitter formed by screen printing technology

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Large-area bifacial n-TOPCon solar cells with in situ phosphorus-doped LPCVD poly-Si passivating contacts

Selective tunnel oxide passivated contact on the emitter of large-size n-type TOPCon bifacial solar cells

Impact of Boron Doping Concentration on Tunnel Oxide Passivated Contact in Front Surface for N-Type Poly-Si Based Passivated Contact Bifacial Solar Cells

The 18.3% Silicon Solar Cells with Nano-Structured Surface and Rear Emitter

24.58% total area efficiency of screen-printed, large area industrial silicon solar cells with the tunnel oxide passivated contacts (i-TOPCon) design

Screen-printed n-type industry solar cells with tunnel oxide passivated contact doped by phosphorus diffusion

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

Emitter formation with boron diffusion from PECVD deposited boron-doped silicon oxide for high-efficiency TOPCon solar cells

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

Bifacial silicon heterojunction solar cells using transparent‐conductive‐oxide‐ and dopant‐free electron‐selective contacts

Fabrication and Detailed Analysis of 22.0% Rear Junction Double-side TOPCon Solar Cell with Front SiOx/Polysilicon Selective Emitter

Bifacial p-Type PERC Solar Cell with Efficiency over 22% Using Laser Doped Selective Emitter

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells

Mass production of industrial tunnel oxide passivated contacts (i‐TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W

Development of TOPCon tunnel-IBC solar cells with screen-printed fire-through contacts by laser patterning