Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

n-Type polysilicon passivating contact for industrial bifacial n-type solar cells

Fully screen-printed bifacial large area 22.6% N-type Si solar cell with lightly doped ion-implanted boron emitter and tunnel oxide passivated rear contact

Approaching 23% with large‐area monoPoly cells using screen‐printed and fired rear passivating contacts fabricated by inline PECVD

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Large-area bifacial n-TOPCon solar cells with in situ phosphorus-doped LPCVD poly-Si passivating contacts

Thin Al2O3 passivated boron emitter of n-type bifacial c-Si solar cells with industrial process

Impact of Boron Doping Concentration on Tunnel Oxide Passivated Contact in Front Surface for N-Type Poly-Si Based Passivated Contact Bifacial Solar Cells

SiO 2 Passivation Layer Grown by Liquid Phase Deposition for N-type Bifacial Silicon Solar Cells

21.3%-Efficient N-Type Silicon Solar Cell with a Full Area Rear TiOx/LiF/Al Electron-Selective Contact

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

Numerical and experimental exploration towards a 26% efficiency rear-junction n-type silicon solar cell with front local-area and rear full-area polysilicon passivated contacts

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

High-efficiency n-TOPCon bifacial solar cells with selective poly-Si based passivating contacts

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

Application of n‐Polysilicon Rear Emitter for High‐Efficiency p‐TOPCon Solar Cells

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells

Plasma enhanced chemical vapor‐deposited SiOx(Ny)/n‐type polysilicon on oxide passivating contacts in industrial back‐contacted Si solar cells

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Poly-crystalline silicon-oxide films as carrier-selective passivating contacts for c-Si solar cells

Interplay of annealing temperature and doping in hole selective rear contacts based on silicon-rich silicon-carbide thin films

Ga-doped Czochralski silicon with rear p-type polysilicon passivating contact for high-efficiency p-type solar cells