Abstract:Crystalline silicon (c-Si) solar cells with passivation stacks consisting of a polycrystalline silicon (poly-Si) layer and a thin interfacial silicon dioxide (SiO2) layer show high conversion efficiencies. Since the poly-Si layer in this structure acts as a carrier transport layer, high doping of the poly-Si layer is crucial for high conductivity and the efficient transport of charge carriers from the bulk to a metal contact. In this respect, conventional furnace-based high-temperature doping methods are limited by the solid solubility of the dopants in silicon. This limitation particularly affects p-type doping using boron. Previously, we showed that laser activation overcomes this limitation by melting the poly-Si layer, resulting in an active concentration beyond the solubility limit after crystallization. High electrically active boron concentrations ensure low contact resistivity at the (contact) metal/semiconductor interface and allow for the maskless patterning of the poly-Si layer by providing an etch-stop layer in an alkaline solution. However, the high doping concentration degrades during long high-temperature annealing steps. Here, we performed a test of the stability of such a high doping concentration under thermal stress. The active boron concentration shows only a minor reduction during SiNx:H deposition at a moderate temperature and a fast-firing step at a high temperature and with a short exposure time. However, for an annealing time tanneal = 30 min and an annealing temperature 600 °C ≤ Tanneal≤ 1000 °C, the high conductivity is significantly reduced, whereas a high passivation quality requires annealing in this range. We resolve this dilemma by introducing a second, healing laser reactivation step, which re-establishes the original high conductivity of the boron-doped poly-Si and does not degrade the passivation. After a thermal annealing temperature Tanneal = 985 °C, the reactivated layers show high sheet conductance (Gsh) with Gsh = 24 mS sq and high passivation quality, with the implied open-circuit voltage (iVOC) reaching iVOC = 715 mV. Therefore, our novel three-step process consisting of laser activation, thermal annealing, and laser reactivation/healing is suitable for fabricating highly efficient solar cells with p++-poly-Si/SiO2 contact passivation layers.

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Phosphorus-doped polycrystalline silicon passivating contacts via spin-on doping

Poly-Si passivating contacts prepared via phosphorus spin-on-doping: A comparison between different silicon deposition methods

Phosphorus-diffused polysilicon contacts for solar cells

A High-Quality Dopant-Free Electron-Selective Passivating Contact Made from Ultra-Low Concentration Water Solution

Current status and challenges for hole-selective poly-silicon based passivating contacts

Impurity Gettering by Boron‐ and Phosphorus‐Doped Polysilicon Passivating Contacts for High‐Efficiency Multicrystalline Silicon Solar Cells

Blistering-free carbon-doped polysilicon (n+) passivating contact with high surface passivation properties prepared by industrial tube PECVD

Three-Step Process for Efficient Solar Cells with Boron-Doped Passivated Contacts

A silicon oxide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 23%

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

Optimizing Phosphorus-Doped Polysilicon in TOPCon Structures Using Silicon Oxide Layers to Improve Silicon Solar Cell Performance

Polysilicon Passivating Contacts for Silicon Solar Cells: Interface Passivation and Carrier Transport Mechanism

Conductive Hole-Selective Passivating Contacts for Crystalline Silicon Solar Cells

Regionalizing Nitrogen Doping of Polysilicon Films Enabling High‐Efficiency Tunnel Oxide Passivating Contact Silicon Solar Cells

Passivating Contact with Phosphorus‐Doped Polycrystalline Silicon‐Nitride with an Excellent Implied Open‐Circuit Voltage of 745 mV and Its Application in 23.88% Efficiency TOPCon Solar Cells

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

Poly-crystalline silicon-oxide films as carrier-selective passivating contacts for c-Si solar cells

Optimization of In-situ and Ex-situ doped p+ Passivating Contact for High Efficiency p-TOPCon Solar Cell Application

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

Blistering-free polycrystalline silicon carbide films for double-sided passivating contact solar cells