Abstract:Crystalline silicon (c-Si) solar cells with passivation stacks consisting of a polycrystalline silicon (poly-Si) layer and a thin interfacial silicon dioxide (SiO2) layer show high conversion efficiencies. Since the poly-Si layer in this structure acts as a carrier transport layer, high doping of the poly-Si layer is crucial for high conductivity and the efficient transport of charge carriers from the bulk to a metal contact. In this respect, conventional furnace-based high-temperature doping methods are limited by the solid solubility of the dopants in silicon. This limitation particularly affects p-type doping using boron. Previously, we showed that laser activation overcomes this limitation by melting the poly-Si layer, resulting in an active concentration beyond the solubility limit after crystallization. High electrically active boron concentrations ensure low contact resistivity at the (contact) metal/semiconductor interface and allow for the maskless patterning of the poly-Si layer by providing an etch-stop layer in an alkaline solution. However, the high doping concentration degrades during long high-temperature annealing steps. Here, we performed a test of the stability of such a high doping concentration under thermal stress. The active boron concentration shows only a minor reduction during SiNx:H deposition at a moderate temperature and a fast-firing step at a high temperature and with a short exposure time. However, for an annealing time tanneal = 30 min and an annealing temperature 600 °C ≤ Tanneal≤ 1000 °C, the high conductivity is significantly reduced, whereas a high passivation quality requires annealing in this range. We resolve this dilemma by introducing a second, healing laser reactivation step, which re-establishes the original high conductivity of the boron-doped poly-Si and does not degrade the passivation. After a thermal annealing temperature Tanneal = 985 °C, the reactivated layers show high sheet conductance (Gsh) with Gsh = 24 mS sq and high passivation quality, with the implied open-circuit voltage (iVOC) reaching iVOC = 715 mV. Therefore, our novel three-step process consisting of laser activation, thermal annealing, and laser reactivation/healing is suitable for fabricating highly efficient solar cells with p++-poly-Si/SiO2 contact passivation layers.

Blistering-free polycrystalline silicon carbide films for double-sided passivating contact solar cells

Dual-functional carbon-doped polysilicon films for passivating contact solar cells: regulating physical contacts while promoting photoelectrical properties

Bi-layer in-situ phosphorus doped poly-Si films by PECVD for blistering-free high-efficiency industrial TOPCon solar cells

Blistering-free carbon-doped polysilicon (n+) passivating contact with high surface passivation properties prepared by industrial tube PECVD

Poly-crystalline silicon-oxide films as carrier-selective passivating contacts for c-Si solar cells

Influence of contact characteristics of SnO2/P on fill factor of solar cell

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Poly-Si passivating contacts prepared via phosphorus spin-on-doping: A comparison between different silicon deposition methods

Phosphorus-doped polycrystalline silicon passivating contacts via spin-on doping

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

The Passivation Characteristics of Poly-Si/SiOx Stack for High-Efficiency Silicon Solar Cells

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

A silicon oxide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 23%

Ga-doped Czochralski silicon with rear p-type polysilicon passivating contact for high-efficiency p-type solar cells

Polysilicon Passivating Contacts for Silicon Solar Cells: Interface Passivation and Carrier Transport Mechanism

Design Rule of Electron- and Hole-Selective Contacts for Polycrystalline Silicon-Based Passivating Contact Solar Cells

Phosphorus-diffused polysilicon contacts for solar cells

Improved interface passivation by optimizing a polysilicon film under different hydrogen dilution in N-type TOPCon silicon solar cells

Investigation on the passivated Si/Al2O3 interface fabricated by non-vacuum spatial atomic layer deposition system

Material Properties of Nanocrystalline Silicon Carbide for Transparent Passivating Contact Solar Cells

Three-Step Process for Efficient Solar Cells with Boron-Doped Passivated Contacts