Abstract:We present a systematic study of highly boron (B)-doped poly-silicon (p+-poly-Si) and ultrathin silicon oxide (SiOx) bi-layer structure, also named as p-TOPCon, as the hole-selective passivated contact on n-type c-Si wafer, where the SiOx layer is made with three methods of hot nitric acid oxidation SiOx (NAOS-SiOx), plasma-assisted nitrous-oxide (N2O) gas oxidation (PANO-SiOx), and thermal oxidation (Thermal-SiOx). We demonstrate that the SiOx has a strong influence on the passivation quality. The best result is achieved using the Thermal-SiOx, while the NAOS-SiOx is slightly inferior, but better than the PANO-SiOx. The p+-poly-Si/SiOx structures with the three SiOx layers achieve the optimized passivation quality at different annealing temperatures of 820 °C for the NAOS-SiOx, 880 °C for the PANO-SiOx, and 930 °C for the Thermal-SiOx. The other potential factors affecting the passivation quality are also studied. The most important observation is that the optimized p-TOPCon structures with the three SiOx layers have a similar B diffusion profile, which penetrates into the c-Si wafer about 50 nm with B concentration decreasing to ~1 × 1018 cm−3. However, the overall p+-poly-Si/SiOx is still much poorer than n+-poly-Si/SiOx in terms the passivation quality. The comparison of the τeff versus carrier injection intensity spectra suggests that the B–O complex is the passivation killer possibly, and the approaches to improve the p-TOPCon are searching the other elements to reduce the B–O defects. In addition, contact resistivity (ρc) measurements show that the Thermal-SiOx leads a higher ρc than the others, but its value is still low enough for high-efficiency solar cells.

Influence of contact characteristics of SnO2/P on fill factor of solar cell

Tuning of the Contact Properties for High-Efficiency Si/PEDOT:PSS Heterojunction Solar Cells

Electron‐Selective Strontium Oxide Contact for Crystalline Silicon Solar Cells with High Fill Factor

Chromium Trioxide Hole-Selective Heterocontacts for Silicon Solar Cells

Highly Conductive p-Type Silicon Carbon Alloys Deposited by Hot-Wire Chemical Vapor Deposition

Effect of Surface Texture on Pinhole Formation in SiO x-Based Passivated Contacts for High-Performance Silicon Solar Cells

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

Improved V 2 O X Passivating Contact for p ‐Type Crystalline Silicon Solar Cells by Oxygen Vacancy Modulation with a SiO X Tunnel Layer

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

Annealing-free, electron-selective ohmic contacts using zirconium oxide and aluminum for n-type crystalline silicon solar cells

Improved Device Performance of Si-based Heterojunction Solar Cells by Using Phosphorus Doped Si Nanocrystals Embedded in SiC Host Matrix

Conductive Hole-Selective Passivating Contacts for Crystalline Silicon Solar Cells

Material Properties of Nanocrystalline Silicon Carbide for Transparent Passivating Contact Solar Cells

Effective Hydrogenation Strategies to Boost Efficiency over 20% for Crystalline Silicon Solar Cell with Al2O3/Cu2O Passivating Contact

A Strategy to Optimize Nickel Oxide/Crystalline Silicon Heterocontact of HJT Solar Cells

Comparison of different types of interfacial oxides on hole-selective p+-poly-Si passivated contacts for high-efficiency c-Si solar cells

Interfacial engineering of ZnS passivating contacts for crystalline silicon solar cells achieving 20% efficiency

Effects on Metallization of n+-Poly-Si Layer for N-Type Tunnel Oxide Passivated Contact Solar Cells

Efficient silicon solar cells with highly conductive zirconium nitride electron-selective contacts

Exploring co-sputtering of ZnO:Al and SiO2 for efficient electron-selective contacts on silicon solar cells

Effect of the interface glass on electrical performance of screen printed Ag thick-film contacts of Si solar cells