Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Ga-doped Czochralski silicon with rear p-type polysilicon passivating contact for high-efficiency p-type solar cells

Investigation Of Low-Cost And High Efficiency Ga-Doped Cz-Si Solar Cells

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Investigating the viability of PERC solar cells fabricated on Ga- instead of B-doped monocrystalline silicon wafer

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

Application of SiO2 Passivation Technique in Mass Production of Silicon Solar Cells

Passivated Emitter and Rear Cell Silicon Solar Cells with a Front Polysilicon Passivating Contacted Selective Emitter

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Design and Optimization of SiOx/AZO Transparent Passivating Contacts for High‐Efficiency Crystalline Silicon Solar Cells

Efficient Silicon Solar Cells with Aluminum‐Doped Zinc Oxide‐Based Passivating Contact

Impurity Gettering by Boron‐ and Phosphorus‐Doped Polysilicon Passivating Contacts for High‐Efficiency Multicrystalline Silicon Solar Cells

Interfacial engineering of ZnS passivating contacts for crystalline silicon solar cells achieving 20% efficiency

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

Poly-crystalline silicon-oxide films as carrier-selective passivating contacts for c-Si solar cells

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

The Passivation Characteristics of Poly-Si/SiOx Stack for High-Efficiency Silicon Solar Cells

Gallium‐Doped Silicon for High‐Efficiency Commercial Passivated Emitter and Rear Solar Cells

Ga-doped ZnO rear transparent contact enables high efficiency silicon heterojunction solar cells

Numerical and experimental exploration towards a 26% efficiency rear-junction n-type silicon solar cell with front local-area and rear full-area polysilicon passivated contacts

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells