Abstract:We present a systematic study of highly boron (B)-doped poly-silicon (p+-poly-Si) and ultrathin silicon oxide (SiOx) bi-layer structure, also named as p-TOPCon, as the hole-selective passivated contact on n-type c-Si wafer, where the SiOx layer is made with three methods of hot nitric acid oxidation SiOx (NAOS-SiOx), plasma-assisted nitrous-oxide (N2O) gas oxidation (PANO-SiOx), and thermal oxidation (Thermal-SiOx). We demonstrate that the SiOx has a strong influence on the passivation quality. The best result is achieved using the Thermal-SiOx, while the NAOS-SiOx is slightly inferior, but better than the PANO-SiOx. The p+-poly-Si/SiOx structures with the three SiOx layers achieve the optimized passivation quality at different annealing temperatures of 820 °C for the NAOS-SiOx, 880 °C for the PANO-SiOx, and 930 °C for the Thermal-SiOx. The other potential factors affecting the passivation quality are also studied. The most important observation is that the optimized p-TOPCon structures with the three SiOx layers have a similar B diffusion profile, which penetrates into the c-Si wafer about 50 nm with B concentration decreasing to ~1 × 1018 cm−3. However, the overall p+-poly-Si/SiOx is still much poorer than n+-poly-Si/SiOx in terms the passivation quality. The comparison of the τeff versus carrier injection intensity spectra suggests that the B–O complex is the passivation killer possibly, and the approaches to improve the p-TOPCon are searching the other elements to reduce the B–O defects. In addition, contact resistivity (ρc) measurements show that the Thermal-SiOx leads a higher ρc than the others, but its value is still low enough for high-efficiency solar cells.

Design and Optimization of SiOx/AZO Transparent Passivating Contacts for High‐Efficiency Crystalline Silicon Solar Cells

A silicon carbide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 24%

Efficient Silicon Solar Cells with Aluminum‐Doped Zinc Oxide‐Based Passivating Contact

A silicon oxide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 23%

Improved V 2 O X Passivating Contact for p ‐Type Crystalline Silicon Solar Cells by Oxygen Vacancy Modulation with a SiO X Tunnel Layer

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

Self‐Diffusion Effect Assisted TiO2/Li3PO4 Electron Selective Passivating Contact in Silicon Solar Cells Approaching 23% Efficiency

Full-Area i-a-Si:H/ATO/Mg Electron-Selective Contacts for Silicon Solar Cells

Poly-crystalline silicon-oxide films as carrier-selective passivating contacts for c-Si solar cells

Interfacial engineering of ZnS passivating contacts for crystalline silicon solar cells achieving 20% efficiency

Effective Hydrogenation Strategies to Boost Efficiency over 20% for Crystalline Silicon Solar Cell with Al2O3/Cu2O Passivating Contact

Novel Passivation and Gettering Strategy for Silicon Wafer by Al2O3/n‐poly‐Si/SiOx Stack for High‐Efficiency p‐Type Passivating Tunnel Oxide Contact Solar Cells

Highly transparent oxygen‐doped poly‐Si with in‐situ N2O oxidant for poly‐Si passivating contacts in perovskite/silicon tandem solar cells

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

21.16%-efficiency p-type TOPCon solar cell with ALD-Al2O3/MoOx/Ag as a hole-selective passivating contact

Simulation of a Charged Al2O3 Film as an Assisting Passivation Layer for a-Si Passivated Contact P-Type Silicon Solar Cells

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

A High-Quality Dopant-Free Electron-Selective Passivating Contact Made from Ultra-Low Concentration Water Solution

Chromium Trioxide Hole-Selective Heterocontacts for Silicon Solar Cells

Comparison of different types of interfacial oxides on hole-selective p+-poly-Si passivated contacts for high-efficiency c-Si solar cells