Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Passivated Emitter and Rear Cell Silicon Solar Cells with a Front Polysilicon Passivating Contacted Selective Emitter

Study on selective emitter fabrication through an innovative pre‐diffusion process for enhanced efficiency in TOPCon solar cells

TOPerc solar cell: An integral approach of TOPCon and PERC architectures for achieving efficiency beyond 25%

Quantitative Understanding and Implementation of Screen Printed p+ Poly-Si/Oxide Passivated Contact to Enhance the Efficiency of p-PERC Cells

Performance of Large Area n-TOPCon Solar Cells with Selective Poly-Si Based Passivating Contacts Prepared by PECVD Method

Selective tunnel oxide passivated contact on the emitter of large-size n-type TOPCon bifacial solar cells

Numerical study of mono-crystalline silicon solar cells with passivated emitter and rear contact configuration for the efficiency beyond 24% based on mass production technology

Electrical Performance, Loss Analysis, and Efficiency Potential of Industrial‐Type PERC, TOPCon, and SHJ Solar Cells: A Comparative Study

Improved Bifacial Properties of P‐Type Passivated Emitter and Rear Cell Solar Cells toward High Mass Production Efficiency

Optimization of efficiency enhancement of TOPCon cells with boron selective emitter

High-efficiency n-TOPCon bifacial solar cells with selective poly-Si based passivating contacts

Pathway towards 24% efficiency for fully screen-printed passivated emitter and rear contact solar cells

22.13% Efficient Industrial P-Type Mono Perc Solar Cell

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

A solid strategy to realize heteroface selective emitter and rear passivated silicon solar cells

Characterization of 23-percent efficient silicon solar cells

Optimization of Controllable Factors in the Aluminum Silicon Eutectic Paste and Rear Silicon Nitride Mono-Passivation Layer of PERC Solar Cells

How to make PERC suitable for perovskite–silicon tandem solar cells: A simulation study

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

Industrial Silicon Solar Cells Applying the Passivated Emitter and Rear Cell (PERC) Concept—A Review

Highly passivated TOPCon bottom cells for perovskite/silicon tandem solar cells