Abstract:In this paper, a multiple-ring-modulated junction termination extension (MRM-JTE) technology for large-area silicon carbide PiN rectifier rated at 4500 V is proposed and experimentally investigated using a standard two-zone JTE (TZ-JTE) process without extra process steps or masks. Multiple modulation rings embedded inside JTE region, which is similar to varied lateral doping technology widely used in silicon devices, form a gradual decrease of effective charges in the termination region. MRM combines the advantages of two termination techniques, namely, ring-assisted JTE and space-modulated JTE, to enlarge the optimum JTE-dose window with high reverse blocking voltage in comparison with conventional TZ-JTE. A breakdown voltage of 4940 V at a leakage current of 1 mu A is achieved from fabricated MRM-JTE rectifiers with a 36-mu m-thick N-epilayer doped to 1.8 x 10(15) cm(-3), which is 92% of the ideal parallel-plane value. A forward current of 50 A has been measured at a forward voltage drop of 3.9 V for devices with an active anode area of 9.2 mm(2), corresponding to low differential on-resistance of 1.8 m Omega.cm(2). The simulation and experimental results show that the proposed device exhibits approximately 2 times JTE dose tolerance window improvement with respect to the breakdown voltage of 4500 V.

Expanding the Dose Window of Step-Etched Space-Modulated JTE for Ultrahigh Voltage 4H-Sic Devices

Improved Etched Multistep JTE for UHV SiC Power Devices

An Improved Composite JTE Termination Technique for Ultrahigh Voltage 4H-Sic Power Devices

Etched Junction Termination Extension With Floating Guard Rings And Middle Rings For Ultrahigh-Voltage 4h-Sic Pin Diodes

Step JTE, an Edge Termination for UHV SiC Power Devices with Increased Tolerances to JTE Dose and Surface Charges

Hybrid Termination with Wide Trench for 4H-Sic Super-Junction Devices

Bevel Junction Termination Extension—A New Edge Termination Technique for 4H-Sic High-Voltage Devices

A New Edge Termination Technique for High-Voltage Devices in 4H-Sic–multiple-floating-zone Junction Termination Extension

Multi-Step Junction Termination Extension Design and Simulation Study for 4H-Sic Schottky Barrier Diode

Implantation-free 2-Step Junction Termination Extension with 2-Space Modulated Buffer Trench Regions for UHV 4H-SÍC GTO Thyristors

Development of G10kv 4H-Sic SBD Junction Extension Termination

A Multiple-Ring-Modulated JTE Technique for 4H-Sic Power Device with Improved JTE-Dose Window

Single-Implant, Field Plate and Guard Rings Assist Multi-Zone Graded Jte for 4H-Sic P-I-N Diodes

High Voltage SiC JBS Diodes with Multiple Zone Junction Termination Extension Using Single Etching Step

4H-Sic BJTs with Epitaxial Junction Termination Composite Structure

Characterization and Fabrication of the CFM-JTE for 4H-Sic Power Device with High-Efficiency Protection and Increased JTE Dose Tolerance Window

Two-mesa, guard rings assisted two-zone JTE for ultrahigh-voltage(>10kv) 4H-SiC p-i-n diodes

A Study of the High-K Enhanced Depletion-JTE for Ultra-High Voltage SiC Power Device with Improved JTE-Dose Window

Practical One-Step Solution of Smoothly Tapered Junction Termination Extension for High Voltage SiC Gate Turn-off Thyristor

An Effective High-Voltage Termination for Sic Planar Pn Junctions for Use in High-Voltage Devices and Uv Detectors

Implantation-free SiC Thyristor with Single-Mask 3D Termination Near 10 Kv