Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Homogenization Treatment and Plastic Deformation Improve the Carbide Homogeneity of M42 High-Speed Steel

Development of Powder Metallurgy High Speed Steel

High-Temperature Annealing Significantly Enhances Intrinsic Hot Workability of the As-cast High-Nitrogen M42 High-Speed Steel

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Study on the Influence of Silicon and Aluminum on the Microstructure and Properties of Low Cobalt M42 High-Speed Steel

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment

Improved high‐temperature softening resistance and wear resistance of AISI M42 high‐speed steel by N‐alloying

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Effect of Alloying and Microalloying Elements on Carbides of High-Speed Steel: An Overview

Influence Mechanism of Slow Cooling Treatment after Homogenization on Hot Deformation Behavior of a New Nickel-Based Superalloy

Influence of Co on the microstructure and mechanical properties of M42 high-speed steel

Effect of Tempering Conditions on Secondary Hardening of Carbides and Retained Austenite in Spray-Formed M42 High-Speed Steel

Microstructure and Mechanical Properties of B4C-Blended M3:2 High-Speed Steel Powders Consolidated by Sintering and Heat Treatment

Superior Mechanical Properties of M35 High-Speed Steel Obtained by Controlling Carbide Precipitation and Distribution Via Electropulsing Treatment

Microstructure Evolution and Precipitation Strengthening Behaviour of Additively Manufactured High-speed Steels

The Transformation of Carbides during Austenization and Its Effect on the Wear Resistance of High Speed Steel Rolls

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Mechanical and tribological assessments of high-vanadium high-speed steel by the conventional powder metallurgy process

Microstructure and Mechanical Properties of H13 Steel/High-Speed Steel Composites Prepared by Laser Metal Deposition

Effect of Secondary Aerosol Cooling on the Characteristics of Carbides in M42 High‐Speed Steel Produced by the Electroslag Remelting Withdrawal Process

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment