Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Microstructure and Mechanical Properties of B4C-Blended M3:2 High-Speed Steel Powders Consolidated by Sintering and Heat Treatment

Development of Powder Metallurgy High Speed Steel

Microstructure and Properties of Cast B-Bearing High Speed Steel

Analyzing the Effect of CeB6 on Microstructure and Mechanical Properties of High-Speed Steel Consolidated by Powder Metallurgy

Microstructure and Hardening Behavior of Al-modified Fe-1.5 Wt%b-0.4 Wt%c High-Speed Steel During Heat Treatment

Microstructural changes of high speed steel powders during heating in vacuum

Enhancement mechanical properties of in-situ preparated B4C-based composites with small amount of (Ti3SiC2+Si)

A modified M2 high-speed steel enhanced by in-situ synthesized core-shell MC carbides

Microstructural Evolution and Mechanical Properties of the Aluminum-Alloyed Fe-1.50 Wt%B-0.40 Wt%C High-Speed Steel

Homogenization Treatment and Plastic Deformation Improve the Carbide Homogeneity of M42 High-Speed Steel

Effects of Silicon Addition on Tempering Phase and Mechanical Properties of Sintered M3:2 High-Speed Steel

The Effect of B4C on the Microstructure and Thermo-Mechanical Properties of HfB2-based Ceramics

Microstructure and mechanical properties of B4C based ceramics with Fe3Al as sintering aid by spark plasma sintering

The effect of B and Ti–Al intermetallics additions on the microstructure and mechanical properties of hot-pressed B4C

Influence of Co on the microstructure and mechanical properties of M42 high-speed steel

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Study on the Influence of Silicon and Aluminum on the Microstructure and Properties of Low Cobalt M42 High-Speed Steel

Microstructural Evolution, Behavior of Precipitates, and Mechanical Properties of Powder Metallurgical High-Speed Steel S390 During Tempering

B4C-SiC skeleton reinforced graphite composites with excellent mechanical properties

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting