Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Study on the Influence of Silicon and Aluminum on the Microstructure and Properties of Low Cobalt M42 High-Speed Steel

Influence of Co on the microstructure and mechanical properties of M42 high-speed steel

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Development of Powder Metallurgy High Speed Steel

Homogenization Treatment and Plastic Deformation Improve the Carbide Homogeneity of M42 High-Speed Steel

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Improved high‐temperature softening resistance and wear resistance of AISI M42 high‐speed steel by N‐alloying

Microstructure and Mechanical Properties of B4C-Blended M3:2 High-Speed Steel Powders Consolidated by Sintering and Heat Treatment

Effect of Alloying and Microalloying Elements on Carbides of High-Speed Steel: An Overview

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Analysis of interface microstructure and element diffusion of WC-Co-Ni-Fe powder and M2 high-speed steel composite

High-Temperature Annealing Significantly Enhances Intrinsic Hot Workability of the As-cast High-Nitrogen M42 High-Speed Steel

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Microstructure, Mechanical Properties, and Oxidation Resistance of Nanocomposite Ti–Si–N Coatings

A modified M2 high-speed steel enhanced by in-situ synthesized core-shell MC carbides

Carbides in High-Speed Steels Containing Silicon

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Influence of Tempering Time on the Microstructure and Mechanical Properties of AISI M42 High-Speed Steel

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Effects of Co on Mechanical Properties and Precipitates in a Novel Secondary-Hardening Steel with Duplex Strengthening of M2C and β-NiAl

Experimental Study on Surface Microscopic Characteristics of scCO2-MQL Milled γ-TiAl Alloy