Abstract:This paper presents a comprehensive investigation of the effects of cutting parameters on the surface integrity of milled γ-TiAl alloys. Surface topography, surface roughness, surface defects, plastic deformation, micro-hardness, chip morphology, and tool wear of the milled γ-TiAl alloys were analyzed. The results indicate that the feed rate had the greatest influence on the surface topography and surface roughness. The value of surface roughness increased with the increase in cutting depth and feed rate. However, with the increase in cutting speed, it initially increased and then decreased. The minimum surface roughness was found to be 0.066 μm. The thickness of the plastic deformation layer and the micro-hardness value increased with the increase in cutting depth and feed rate. Also, they initially increased and then decreased with the increase in cutting speed. The minimum thickness of the plastic deformation layer was 15 μm and the depth of the hardened layer on the processed surface varied between 55 and 70 μm. The chip morphology was closely related to the quality of the processed surface. When the cutting depth and feed rate decreased, the chip morphology was transformed from segmented to nearly smooth. When the cutting depth and feed rate reached a critical point, plastic processing of γ-TiAl was achieved. Compared to brittle deformation, a more favorable processed surface was obtained. Finally, the comparison tests of tool wear were carried out with dry and flood coolant cutting. When the cutting speed reached 120 m/min in dry cutting, the tool life was very poor, and the cutting distance was only 1 m. However, the tool life was generally good when cutting with low cutting speed under the following conditions: vc = 60 m/min, ap = 0.1 mm, and fz = 0.01 mm/tooth. Under these conditions, the cutting distance was 60 m in dry cutting with the tool wear of 0.2 mm and 120 m in flood coolant cutting with the tool wear of 0.1 mm. The tool life in flood coolant operation was better than that of dry operation. The tool life decreased to 30 m when cutting with high cutting speed or feed rate (ap = 0.25 mm or fz = 0.025 mm/tooth).

Experimental Study on Surface Microscopic Characteristics of scCO2-MQL Milled γ-TiAl Alloy

Tool Wear and Machined Surface Characteristics in Side Milling Ti6Al4V under Dry and Supercritical CO2 with MQL Conditions

Microstructure- and Cooling/lubrication Environment-Dependent Machining Responses in Side Milling of Direct Metal Laser-Sintered and Rolled Ti6Al4V Alloys

Cooling/Lubrication Performance of Dry and Supercritical CO2-Based Minimum Quantity Lubrication in Peripheral Milling Ti-6Al-4V

Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions

Influence of Thermal Mechanical Coupling on Surface Integrity in Disc Milling Grooving of Titanium Alloy

Experimental Study on Micro-Milling of Ti6Al4V with Minimum Quantity Lubrication

Surface Morphology and Affected Layer in Disc-Milling Grooving of Titanium Alloy

Feasibility of Supercritical CO2-based Minimum Quantity Lubrication to Improve the Surface Integrity of 50% Sip/Al Composites

Microstructure evolution characterization of Ti 2 AlNb intermetallic alloys subjected to side milling

Surface Layer Microstructure and Mechanical Characteristics Analysis of Cast Iron During Milling Process under Supercritical CO2-MQL

Milling Performance Evaluation and Cooling/lubrication Mechanism of Al-50wt% Si Alloy Based on Various Environmentally Sustainable Manufacturing Strategies

Effects of cooling air temperature on cryogenic machining of Ti–6Al–4V alloy

Effect of Minimum Quantity of Lubricant on Carbide Tools and Surface Integrity in the Machining of Titanium Aluminides

Influence of CO2-snow and subzero MQL on thermal aspects in the machining of Ti-6Al-4V

Analysis of Minimum Quantity Lubrication (MQL) for Different Coating Tools During Turning of TC11 Titanium Alloy.

Study on Coated Tool Wear in High-Speed MQL Machining of TC4 Titanium Alloy

Sustainable milling of Ti–6Al–4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment

Computational investigation on the surface cutting of γ-TiAl alloy

Study of surface integrity of milled gamma titanium aluminide

EXPERIMENTAL AND THEORETICAL INVESTIGATIONS ON TOOL WEAR AND SURFACE QUALITY IN MICRO MILLING OF SiCp/AI COMPOSITES UNDER DRY AND MQL CONDITIONS