Abstract:In this work, the effect of Co addition on the solidification velocity, hardness and refined structure trans-formation of the undercooled Ni-Cu-Co alloys have been systematically investigated. The results show that the grain refinement of Ni-Cu-Co ternary alloys at low undercooling is caused by the intense dendrite remelting. However, the grain refinement at high undercooling is attributed to recrystallization, and the driving force of recrystallization comes from the stresses and plastic strains accumulated by the interaction between liquid flow induced by rapid solidification and primary dendrites. The Co addition can significantly increase the solidification velocity and recalescence effect of Ni-Cu-Co alloys by increasing the number of solidified crystal nucleus and solute diffusion velocity. Under the same undercooling level, the increase of solidification velocity and recalescence effect have strengthened the remelting effect and stress accumu-lation, which can enlarge the critical range for grain refinement gradually. Meanwhile, due to the significant improvement of solidification velocity and stress-induced deformation effect by Co addition, the low angle GBs in the refined structure of Ni-Cu-Co alloys increase and the grain size decreases significantly, which have significantly improved the average hardness of the refined structure. When Co addition reaches 6 %, the refined structures can appear in almost the whole undercooling range and the hardness are improved by more than 100 % compared with the as-cast structure.(c) 2022 Elsevier B.V. All rights reserved.

Effects of Co on Mechanical Properties and Precipitates in a Novel Secondary-Hardening Steel with Duplex Strengthening of M2C and β-NiAl

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Homogenizing Effects of Co on Multi-Scale Elemental Distribution in Ru-containing Ni-based Single Crystal Superalloys

Effect of Co Addition on Solidification Velocity, Hardness and Refined Structure Transformation Mechanisms of Undercooled Ni-Cu-Co Alloys

The Effects of Co on the Microstructure and Mechanical Properties of Ni-Based Superalloys Prepared via Selective Laser Melting

Effect of cobalt on precipitation in Fe-Cr-Co-Mo-Ni-C stainless steels

Strengthening of Ni-Mn-Cu-Al-Co steel by nanoscale Cu and β-NiAl co-precipitated couples

Carbide Precipitation and Element Distribution in High Co–Ni Secondary Hardening Steel

Effect of ageing temperature on the microstructural evolution and mechanical properties in M 2 C and NiAl co-precipitation secondary hardening ultrahigh-strength steel

Synergistic Effect of Al and Ni on Microstructure Evolutions and Mechanical Properties of Fe-Mn-Al-C Low-Density Steels

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of cobalt content on the microstructure, microtexture, and mechanical properties of W-Ni-Fe-xCo alloys during solid-phase-sintering and liquid-phase-sintering

Effects of Co content on tensile properties and deformation behaviors of Ni-based disk superalloys at different temperatures

Effect of Co on microstructures and mechanical properties for Nb-Si based in-situ composites

Effects of Fe on microstructure and mechanical properties of CoCrNiFeAl multi-principle elements alloys

Effects of Co on Microstructure, Mechanical Properties, and Corrosion Resistance of Ti-Nb-Zr-Co Biological Alloys

Effects of co-addition of Ni and Al on precipitation evolution and mechanical properties of Fe-Cu alloy

Effects of Cobalt on Solidification Characteristics and As-Cast Microstructure of an Advanced Nickel-Based Single Crystal Superalloys

Effects of trace secondary elements on microstructure and properties in CoCrMnFeNiX0.1 alloys

Effects of Ni on Austenite Stability and Fracture Toughness in High Co-Ni Secondary Hardening Steel

Design of a 2.7 GPa ultra-high-strength high Co–Ni secondary hardening steel by two-step nano-size precipitation tailoring