Abstract:The content of Zn and Mg directly influences the microstructure characteristics of Al–Zn–Mg–Cu alloys. In the present study, the solidification phases of three as-cast Al–Zn–Mg–Cu alloys with different Zn/Mg ratio (1.5, 1.8 and 2.1 at.%, successively) were thoroughly investigated, and their evolutions during homogenizations were analyzed with the aid of optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). The results showed that serious dendritic segregation existed in the as-cast microstructures. In the as-cast alloys with three different Zn/Mg ratio, the secondary phases are represented by non-equilibrium intermetallic phases (Mg(Zn,Cu,Al) 2 and Al 2 Cu) and precipitate MgZn 2 phase. Thereinto, the Mg(Zn,Cu,Al) 2 phase possessed a majority, which was determined through computational analysis of solidification processes. With the increase of Zn/Mg ratio, the amount of Mg(Zn,Cu,Al) 2 phase continuously decreased, while the content of Al 2 Cu phase showed only minor variation. As the Zn/Mg ratio increased, the strength and hardness of the as-cast alloy gradually improved. The Zn/Mg ratio has a significant impact on the dissolution and transformation of the secondary phases during homogenization process. As the Zn/Mg ratio increased, the melting point of the as-cast eutectic gradually decreased. Additionally, due to the higher diffusion rate of Zn compared to Mg and Cu elements, the dissolution rate of the secondary phase increased accordingly. At relatively low temperatures (380, 410, and 440 °C), phase transformation from the Mg(Zn,Cu,Al) 2 phase to the Al 2 CuMg phase occurred in all three alloys. However, phase transformation was only present in Low/Mid-Zn/Mg ratio alloys at 470 °C. These differences are attributed to the varying diffusion rates of Zn, Mg, and Cu elements during the homogenization process. The implementation of a two-stage homogenization process effectively addresses the issue of residual Al 2 CuMg phase in Low/Mid-Zn/Mg ratio alloys.

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Effect of Zn/Mg ratio on the microstructure and mechanical properties of as-cast Al–Zn–Mg–Cu alloys and the phase transformation during homogenization

Homogenization heat treatment of Mg-9.0Y-3.0MM-0.6Zr alloy

Effects of homogenization on the microstructural evolution of a novel Zr and Er containing Al–Mg–Zn alloy

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Homogenization Heat Treatment of Mg-7.68Gd-4.88Y-1.32Nd-0.63Al-0.05Zr Alloy

Effects of Heterogenization Treatment on the Hot-Working Temperature and Mechanical Properties of Al-Cu-Mg-Mn-(Zr) Alloys

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment

Homogenization Treatment of Mg?6Zn?3Sn (wt.％) Alloy and Its Effects on Microstructure and Mechanical Properties

Effects of electromagnetic stirring and subsequent homogenization treatment on the microstructure and mechanical properties of Al70Zn10Mg10Cu5Si5 multi-component alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

Enhanced elevated-temperature mechanical properties of hot-rolled Al–Cu alloys: effect of zirconium addition and homogenization

Synergistic effect of gradient Zn content and multiscale particles on the mechanical properties of Al–Zn–Mg–Cu alloys with coupling distribution of coarse–fine grains

The evolution mechanism of the second phase during homogenization of Al-Zn-Mg-Cu aluminum alloy

Effect of double-step homogenization treatments on the microstructure and mechanical properties of Al–Cu–Li–Zr alloy

Optimizing mechanical property of spray formed Al-Zn-Mg-Cu alloy by combination of homogenization and warm-rolling

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Solidification Paths and Phase Components at High Temperatures of High-Zn Al-Zn-Mg-Cu Alloys with Different Mg and Cu Contents

Research on Homogenization Treatment of Mg-8wt.% Sn-1.5 Wt.% Al Alloy

Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy