Abstract:Developing high-performance simpler alloys via simpler processing procedures is of great significance in achieving carbon dioxide emission peak and carbon neutrality. In the present study, room-temperature (RT) rolling was carried out on simple ternary Al–8Zn–1Mg alloy in order to improve its comprehensive performance by regulating microstructure evolution. Ultimate tensile strength (UTS), yield strength (YS), fracture elongation (EL%) and uniform elongation (EU%) were tested. Optical microscopy (OM), electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were used to characterize the microstructure evolution. Phase analysis was performed by X-ray diffraction (XRD). The results show that RT rolling significantly enhances the UTS and YS of ternary Al–8Zn–1Mg alloy, which are ∼447 MPa and ∼389 MPa, respectively, with the corresponding EL% and EU% of ∼7.1% and ∼4.1%. The comprehensive tensile properties are comparable to or even better than that of their conventional counterparts with more complex compositions or produced by more complicated techniques. Compared with the as-SS alloy, the as-SS + R alloy experiences an additional 227 MPa increase in YS. The calculated results show that fine-grain strengthening and dislocation strengthening (predominantly in the form of microbands in the present study) respectively contribute to 21 MPa and 167 MPa increases in YS. The remaining 40 MPa increase is highly likely derived from the hetero-deformation induced (HDI) strengthening of the heterostructured lamellar microbands. The delicate balance between strength and elongation is mainly attributed to the profuse microbands formed by the coupling effect of high Zn solute atoms and stress. The findings shed light on a fundamental facet of how regulating microbands can develop high performance simpler aluminum alloys which have potential applications in strength-based structural materials.

Enhanced elevated-temperature mechanical properties of hot-rolled Al–Cu alloys: effect of zirconium addition and homogenization

Effects of Heterogenization Treatment on the Hot-Working Temperature and Mechanical Properties of Al-Cu-Mg-Mn-(Zr) Alloys

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of double-step homogenization treatments on the microstructure and mechanical properties of Al–Cu–Li–Zr alloy

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Enhancing properties of Al-Zn-Mg-Cu alloy through microalloying and heat treatment

Enhanced thermal stability and mechanical properties of high-temperature resistant Al−Cu alloy with Zr and Mn micro-alloying

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Enhancing mechanical properties and corrosion resistance of a high strength 7A99 Al alloy by introducing pre-rolling in solution and aging treatments

Microstructure and properties of a new Al–Cu–Mg–Zn–Zr–Ti heat resistant aluminum alloy

Optimizing mechanical property of spray formed Al-Zn-Mg-Cu alloy by combination of homogenization and warm-rolling

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Microstructure Characteristics and Elevated-Temperature Tensile Properties of Al-7Si-0.3Mg Alloys with Zr and Hf Addition

Effect of elevated-temperature annealing on microstructureand properties of Cu−0.15Zr alloy

Enhanced tensile strength and ductility of an Al-6Si-3Cu alloy processed by room temperature rolling

Significant enhancement in tensile strength of room-temperature rolled Al–8Zn–1Mg alloy induced by profuse microbands

Micro-alloying effects of Mn and Zr on the evolution of ageing precipitates and high temperature strength of Al-11.5Si–4Cu alloy after a long-time heat exposure