Abstract:Developing high-performance simpler alloys via simpler processing procedures is of great significance in achieving carbon dioxide emission peak and carbon neutrality. In the present study, room-temperature (RT) rolling was carried out on simple ternary Al–8Zn–1Mg alloy in order to improve its comprehensive performance by regulating microstructure evolution. Ultimate tensile strength (UTS), yield strength (YS), fracture elongation (EL%) and uniform elongation (EU%) were tested. Optical microscopy (OM), electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were used to characterize the microstructure evolution. Phase analysis was performed by X-ray diffraction (XRD). The results show that RT rolling significantly enhances the UTS and YS of ternary Al–8Zn–1Mg alloy, which are ∼447 MPa and ∼389 MPa, respectively, with the corresponding EL% and EU% of ∼7.1% and ∼4.1%. The comprehensive tensile properties are comparable to or even better than that of their conventional counterparts with more complex compositions or produced by more complicated techniques. Compared with the as-SS alloy, the as-SS + R alloy experiences an additional 227 MPa increase in YS. The calculated results show that fine-grain strengthening and dislocation strengthening (predominantly in the form of microbands in the present study) respectively contribute to 21 MPa and 167 MPa increases in YS. The remaining 40 MPa increase is highly likely derived from the hetero-deformation induced (HDI) strengthening of the heterostructured lamellar microbands. The delicate balance between strength and elongation is mainly attributed to the profuse microbands formed by the coupling effect of high Zn solute atoms and stress. The findings shed light on a fundamental facet of how regulating microbands can develop high performance simpler aluminum alloys which have potential applications in strength-based structural materials.

Significant enhancement in tensile strength of room-temperature rolled Al–8Zn–1Mg alloy induced by profuse microbands

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Enhanced tensile strength and ductility of an Al-6Si-3Cu alloy processed by room temperature rolling

Achieving ultrahigh strength in binary Al-10Mg alloy through heavy cryogenic rolling

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Improving the mechanical properties of duplex Mg-Li-Zn alloy by mixed rolling processing

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

A Rolled Mg‐8Al‐1Sm‐1Zn Alloy with High Strength‐Ductility via Single‐Pass Liner Rolling

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Enhancing Mechanical Properties of Rolled Mg-Al-Ca-Mn Alloy Sheet by Zn Addition

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Microstructure and Tensile Properties of Mg-3Al-1Zn Sheets Produced by Hot-Roller-cold-material Rolling

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Effects of Sc Addition and Rolling on the Microstructure and Mechanical Properties of Al–35Zn Alloys

Pre-precipitating promoted by microshear bands effectively circumvents strength-ductility trade-off of RT-rolled Al–6Zn–1Mg alloy

Property Improvements in Fine–grained Mg–Zn–Zr Alloy Sheets Produced by Temperature–step–down Multi–pass Rolling

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Ultra strength-ductility synergy in the Mg-Al-Zn alloy via densely dispersed multi-scale {1012‾} tension twins

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy