Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Effect of Zn on Precipitation Evolution and Mechanical Properties of a High Strength Cast Al-Li-Cu Alloy

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Effect of Zr Content on Formability, Microstructure and Mechanical Properties of Selective Laser Melted Zr Modified Al-4.24Cu-1.97Mg-0.56Mn Alloys

Effect of Minor Sc and Zr Addition on Microstructure and Properties of Ultra-High Strength Aluminum Alloy

Effect of Minor Sc and Zr on Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy

Effects of Zr on Microstructures and Properties of a Β Matrix Mg-13Li-3Al-0.7Zr Alloy

Effect of Zr Addition on Microstructure and Properties of Al–Mn–Si–Zn-based Alloy

Effect of Zirconium on Microstructures and Mechanical Properties of Squeeze Cast Al–5.0Cu–0.4Mn–0.1Ti–0.1RE Alloy

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy

Effect of grain thickness and T 1 precipitate on the strength anisotropy of Al-4.0Cu-1.0Li-0.4Mg-0.4Ag-xZr alloys under different heat treatment

Effect of Zr-Adding on Microstructure and Mechanical Properties for Mg-5Sn Alloy

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Effect of Mn Addition on Microstructure and Mechanical Properties of Cast Al-2li-2cu-0.8mg-0.4zn-0.2zr Alloy

Effect of Zn/Mg Ratio on Microstructure and Properties of Cold Extruded Al-xZn-2.4Mg-0.84Cu-0.2Zr-0.25Ti Aluminum Alloy

Effects of Minor Sc and Zr Additions on Mechanical Properties and Microstructure Evolution of Al−Zn−Mg−Cu Alloys

Microstructures and Mechanical Properties of Al–Zn–Mg–Cu Alloy with the Combined Addition of Ti and Zr

Effect of Sc and Zr on Microstructure and Mechanical Properties of As‐Cast Al–Li–Cu Alloys