Abstract:The microstructure evolution and mechanical properties of Al–3.92Cu–1.10Li–0.68Mg–0.32Ag–0.23Mn–0.35Zn–0.11Zr and Al–3.92Cu–1.12Li–0.76Mg–0.29Ag–0.24Mn–0.24Zn–0.12Zr–0.083Sc (wt%) alloys during homogenization with different cooling modes were comprehensively studied. It was clearly revealed that the minor Sc addition refined the grains of as-cast Al–Cu–Li–Mg alloys through the formation of primary Al3(Sc, Zr) phases during the solidification process, and induced Sc enrichment in the θ (Al2Cu) eutectic. After the homogenization treatment, the majority of coarse nonequilibrium eutectic phases at the grain boundaries dissolved into the α-Al matrix, leading to the relatively uniform distribution of each element. Sc-added alloy after homogenization treatments possessed more superior strength and ductility than Sc-free alloy. Compared to the furnace cooling mode, the air cooling mode could inhibit the precipitation of micron-sized coarse T1 (Al2CuLi) phase and improve the mechanical properties of the alloys. After homogenization, the continuous Al2Cu phase in the as-cast Sc-added alloy dissolved and transformed to an array of W-(Al, Cu, Sc) ternary phase, which was identified as Al6Cu6Sc with the body-centered tetragonal structure. The appearance of spherical Al6Cu6Sc particle could not damage the mechanical properties of Al–Cu–Li–Mg alloys after the homogenization treatment. The tensile strength, yield strength and elongation of Sc-added alloy after the homogenization by air cooling were 390 MPa, 265 MPa and 10.8%, respectively. The investigation of Al6Cu6Sc phase offered a potential avenue to produce high-quality Sc-added 2xxx series alloys.Graphic

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Effect of Minor Sc and Fe Co-Addition on the Microstructure and Mechanical Properties of Al-Cu Alloys During Homogenization Treatment

Effect of Sc content on microstructure characteristics and evolution of W phase in Al–Cu–Li alloys under as-cast and homogenization conditions

Effect of Minor Sc and Zr Addition on Microstructure and Properties of Ultra-High Strength Aluminum Alloy

Effects of Sc on the Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Casting Aluminum Alloy

Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Effect of Minor Scandium Addition on Microstructures and Tensile Properties of Super-High Strength Al-Zn-Cu-Mg-Zr Alloys

The Effect of Sc Addition on Microstructure and Mechanical Properties of As-Cast Zr-containing Al-Cu Alloys

Effects of Minor Sc on the Microstructure and Mechanical Properties of Al-Zn-Mg-Cu-Zr Based Alloys

Effects of Minor Manganese Addition on Microstructures and Tensile Properties of Al-Mg-Si Alloys

Effect of Rare Earth Sc Addition on Microstructure and Mechanical Properties of an Al-Cu-Mg-Ag Alloy

Effect of Sc microalloying on microstructure evolution and mechanical properties of extruded Al-Zn-Mg-Cu alloys

Influence of Sc on microstructure and mechanical properties of Al–Si–Mg–Cu–Zr alloy

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Effects of minor Sc on microstructure and properties of Al-Zn-Mg-Zr alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Effect of minor Sc additions on precipitation and mechanical properties of a new Al-Cu-Li alloy under T8 temper

The influence of Sc solute partitioning on the microalloying effect and mechanical properties of Al-Cu alloys with minor Sc addition

Uncovering the combining V with Ni micro-addition alloying on the mechanical properties and multiphase transformation during solidification and homogenization of Al–Zn–Mg–Cu–Sc alloy