Abstract:The addition of Sc and Zr into an Al–Mg–Mn alloy produced by selective laser melting exhibited exceptional properties. Multiple factors eventually lead to the improvement of properties, such as densification behaviors, grain characteristics, texture and the precipitated phases. We firstly investigate evolution of the melt pool characteristics which are varied under different processing parameters and lead to different solidified microstructures, densification behaviors and corresponding mechanical properties. Meanwhile, the characteristics of melt pool can be predicted through the normalized enthalpy of input energy, which presents more credible relationship with the melt pool dimensions. To this end, the relative density is up to 99.88% when the volume energy density and normalized enthalpy are combined used. Recrystallisation inhabitations induced by the added Sc and Zr is supposed after comparing the grain sizes under different conditions. Regrettably, the relationship between melt pool characteristics and the equiaxed/columnar ratio can not be described accurately, which due to the pseudo-equiaxed regions in XZ/YZ sections through regulating the melt track orientations via 67° scanning rotation. There are dispersed Al6Mn and Al3(Sc, Zr) particles exist in as-fabricated samples result in better mechanical properties and the subsequent aging treatment can further improve the comprehensive mechanical properties. Finally, the ultimate tensile strength and ductility is separately about 494.32 ± 4.16 MPa and 15 ± 1.27% after aging for 4 h at 325 °C. In contrast, the processing parameters have little impact on mechanical properties, especially for the yield strength, mainly owing to the homologous precipitate phase and grain sizes when the relative density is similar. The connection involving the whole periods from solidification to the final mechanical properties is discussed that may offer feasible ideas for alloy design and corresponding parameter optimization.

Microstructure evolution and microhardness of the novel Al–Cu–Li-xSc alloys fabricated by laser rapid melting

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Selective laser melting Al-3.4Mg-0.5Mn-0.8Sc-0.4Zr alloys: From melting pool to the microstructure and mechanical properties

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Influence of Mg Content on Microstructure Coarsening, Molten Pool Size, and Hardness of Laser Remelted Al(- x)-Mg-Sc Alloys

On the Sc induced solidification-heterogeneous microstructure in selective laser melted Al-5Mn alloys

Enhancing the strength of Sc-containing Al-Cu-Li alloys by modifying the precipitation behavior through plastic deformation and heat treatment

Microstructural evolution, precipitation behavior and mechanical properties of a novel Al–Zn–Mg–Cu–Li–Sc–Zr alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Nano-phase transformation of composite precipitates in multicomponent Al-Mg-Si(-Sc) alloys

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Microstructure and Mechanical Properties of a Novel Al-Mg-Sc-Ti Alloy Fabricated by Laser Powder Bed Fusion

Microstructure and Mechanical Properties of Al-Li Alloys with Different Li Contents Prepared by Selective Laser Melting

Uncovering the combining V with Ni micro-addition alloying on the mechanical properties and multiphase transformation during solidification and homogenization of Al–Zn–Mg–Cu–Sc alloy

Selective Laser Melting of Gas Atomized Al–3.02Mg–0.2Sc–0.1Zr Alloy Powder: Microstructure and Mechanical Properties

Microstructure and mechanical properties of as casted Al-Si-Sc-Ce alloys prepared by molten salt electrolysis with varied cooling rate

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys