Abstract:With the advancement of laser powder bed fusion (LPBF) for aluminum alloys, developing novel lightweight Al–Li alloy systems present enormous potential for aerospace applications. Conventional Al–Mg–Li alloys exhibit low densities but suffer from poor strength due to the lack of inherent strengthening phases. In the present work, a novel lightweight Al–Mg–Li–Ag-Sc-Zr alloy was developed for LPBF after optimizing the processing parameters. The as-built alloy featured a bimodal microstructure consisting of fine equiaxed grains and columnar grains. The submicron primary Al 3 (Sc, Zr) phases with a cubic L 1 2 structure served as inoculants for grain refinement and exhibited good coherency with the α-Al matrix. Besides, submicron spherical quasicrystalline T-Mg 32 (Al, Ag) 49 phases of and nanometer rod-shaped S 1 –Al 2 MgLi phases were scattered inside the grains. These results produced a yield strength (σ y ) of 286 ± 8 MPa, ultimate tensile strength (σ UTS ) of 406 ± 3 MPa, and elongation at fracture (ε f ) of 12.5 ± 0.3%. The direct aging at 325 °C for 12 h led to an increase in hardness to a peak value of 170 HV. The secondary phases at the grain boundaries were breached and a large amount of submicron T and S 1 phases within the grains were prominently increased. Besides, spherical Al 3 (Sc, Zr, Li) and tiny δ′-Al 3 Li precipitates were observed in the α-Al matrix. A considerably enhanced σ y of 375 ± 12 MPa and σ UTS of 469 ± 4 MPa were achieved mainly due to the particle strengthening but decreased ε f to 5.8 ± 0.2%. The alloys in both states exhibited a moderate work-hardening capability. The feasibility of LPBF for lightweight Al–Li alloy was successfully established but required further optimization of the alloy composition.

Modulation of LPS-, PHA- and M. tuberculosis-mediated cytokine production by pentoxifylline and thalidomide.

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effects of Li content on microstructure evolution and mechanical properties of squeeze-cast Al-5Cu- x Li alloy assisted with ultrasonic treatment

Effect of Li addition on microstructure and mechanical properties of Al – Mg – Si alloy

Research Progress of New Generation of Aluminum‐Lithium Alloys Alloying

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

The synergistic effect of Li addition on microstructure, texture and mechanical properties of extruded Al–Mg–Si alloys

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

RT ECAP and rolling bestow high strength and good ductility on a low lithium aluminum alloy

Physical metallurgy of aluminum-lithium alloys

Influence of Al-Si eutectic alloy on the mechanical behaviors and microstructure feature of ultralight dual-phase Mg-8Li-x(Al-12.6 Si) alloys

Selective Laser Melting of Gas Atomized Al–3.02Mg–0.2Sc–0.1Zr Alloy Powder: Microstructure and Mechanical Properties

High strength Al–Li alloy development for laser powder bed fusion

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates