Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Effects of Li Content on Phase Evolution and Mechanical Properties of Mg-xLi-6Zn-1.5Y Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Effect of Al addition on microstructure and mechanical properties of Mg−Gd−Zn alloys

Effect of Y content on microstructure evolution and tensile properties of Mg-8Li-3Al-2Sn-xY alloys

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of Al addition on the grain refinement and mechanical properties of as-cast Mg–5Y–4Sm alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

The Effect of Y/Er and Zn Addition on the Microstructure and Mechanical Properties of Mg-11Li Alloy

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Microstructures and mechanical properties of as-extruded Mg–8Gd–2Y–1Zn–6Li alloy

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Effect of Li addition on microstructure and mechanical properties of Al – Mg – Si alloy

The Effect of Zr and Li on the Microstructure of AlMg5Si2Mn-Type Casting Alloys

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy