Abstract:Highlights • A dual phase β+α Mg-Li alloy was fabricated as reducing the Li content. • The dispersed α-Mg phases mitigate the dimension and distribution of eutectic I-Phase along grain boundaries. • The dual phase Mg-Li alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) due to the improved deformation compatibility. • The continuity of slip between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility across interfaces. • Two strengthening mechanisms, nanoscale B2 (Li, Mg) 3 Zn-type precipitates and the microscale I-phase, are characterized. Mg-Li alloys with high lithium concentrations possess a lightweight body-centered cubic (BCC) matrix structure (β-Li). Interspersed eutectics (primarily the reticulated I-phase) often form along phase boundaries (PBs) and grain boundaries (GBs) which strengthen the alloy but cause the loss of ductility due to the brittle behavior of I-phase. By modifying the Li content, we fabricated the (β+α) biphase Mg-Li alloy in which the α-Mg phase with a hexagonal close-packed structure (HCP) is embedded in β-Li matrix, significantly increasing interface density. The high-density interfaces mitigate the distribution and dimension of the I-phase along GBs and PBs. The alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) compared with the alloy without the α-Mg phase (EL = 5.1 %). Structural characterizations unveil the strengthening mechanism of the nanoscale B2 (Li, Mg) 3 Zn-type precipitates in conjunction with the microscale I-phase. The (Li, Mg) 3 Zn nanophases augment the yield and ultimate tensile strength of the alloy without a discernible compromise in ductility, predominantly due to gliding dislocations cutting through the precipitates. In contrast, the microscale I-phase presents a formidable barrier to dislocation motion, facilitating dislocation pileups at interfaces and culminating in diminished ductility across the interface. In-situ stretching techniques were employed to scrutinize the microstructural evolution of alloys during tensile deformation, elucidating that the deformation compatibility of alloys correlates with the average size of the I-phase and their distribution along GBs and PBs. Corresponding to the orientation relationship (OR) between the α-Mg and β-Li phases {110}Li//{0001}Mg and < 1 ̄11 >Li //< 112 ̄0 >Mg, the slip continuity between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility through facilitating the deformation across interfaces. Simultaneously, during the stretching process, the dispersed I-phase instigates the emergence of sporadic microcracks, indicating gradual damage evolution. These discoveries offer novel insights into achieving exceptional strength-ductility amalgamations in Mg-Li alloys through microstructural adjustments.

Effects of Li Content on Phase Evolution and Mechanical Properties of Mg-xLi-6Zn-1.5Y Alloy

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Effect of Y content on microstructure evolution and tensile properties of Mg-8Li-3Al-2Sn-xY alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

The Effect of Y/Er and Zn Addition on the Microstructure and Mechanical Properties of Mg-11Li Alloy

Effects of Icosahedral Phase on Mechanical Anisotropy of As-Extruded Mg-14Li (in Wt%) Based Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Evolutions of Microstructure and Mechanical Properties in Mg–5Li–1Zn–0.5Ag–0.5Zr–xGd Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Enhancing the ductility of cast Mg-Li alloys via dispersed α-Mg phase mitigating the dimension and distribution of interspersed eutectics along grain boundaries

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Influence of Zn Content on Microstructure and Tensile Properties of Mg–Zn–Y–Nd Alloy

Effect of Y on Age Hardening Response and Mechanical Properties of Mg-xY–1.5LPC −0.4zr Alloys

Improved ductility of hot extruded Mg-0.5Zn-0.5Zr-1RE alloy by Li addition

Effects of Li content on microstructure evolution and mechanical properties of squeeze-cast Al-5Cu- x Li alloy assisted with ultrasonic treatment

Effects of LPSO Mg12YZn-Phase on Coefficient of Thermal Expansion and Mechanical Properties of Mg–Y–Zn Alloys

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Microstructures and mechanical properties of as-extruded Mg–8Gd–2Y–1Zn–6Li alloy

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy