Abstract:The content of Zn and Mg directly influences the microstructure characteristics of Al–Zn–Mg–Cu alloys. In the present study, the solidification phases of three as-cast Al–Zn–Mg–Cu alloys with different Zn/Mg ratio (1.5, 1.8 and 2.1 at.%, successively) were thoroughly investigated, and their evolutions during homogenizations were analyzed with the aid of optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). The results showed that serious dendritic segregation existed in the as-cast microstructures. In the as-cast alloys with three different Zn/Mg ratio, the secondary phases are represented by non-equilibrium intermetallic phases (Mg(Zn,Cu,Al) 2 and Al 2 Cu) and precipitate MgZn 2 phase. Thereinto, the Mg(Zn,Cu,Al) 2 phase possessed a majority, which was determined through computational analysis of solidification processes. With the increase of Zn/Mg ratio, the amount of Mg(Zn,Cu,Al) 2 phase continuously decreased, while the content of Al 2 Cu phase showed only minor variation. As the Zn/Mg ratio increased, the strength and hardness of the as-cast alloy gradually improved. The Zn/Mg ratio has a significant impact on the dissolution and transformation of the secondary phases during homogenization process. As the Zn/Mg ratio increased, the melting point of the as-cast eutectic gradually decreased. Additionally, due to the higher diffusion rate of Zn compared to Mg and Cu elements, the dissolution rate of the secondary phase increased accordingly. At relatively low temperatures (380, 410, and 440 °C), phase transformation from the Mg(Zn,Cu,Al) 2 phase to the Al 2 CuMg phase occurred in all three alloys. However, phase transformation was only present in Low/Mid-Zn/Mg ratio alloys at 470 °C. These differences are attributed to the varying diffusion rates of Zn, Mg, and Cu elements during the homogenization process. The implementation of a two-stage homogenization process effectively addresses the issue of residual Al 2 CuMg phase in Low/Mid-Zn/Mg ratio alloys.

Research on Homogenization Treatment of Mg-8wt.% Sn-1.5 Wt.% Al Alloy

Homogenization Treatment of Mg?6Zn?3Sn (wt.％) Alloy and Its Effects on Microstructure and Mechanical Properties

Surface oxidation phenomenon of Mg–10 wt% Sn–1.5 wt% Al alloy during homogenization

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Homogenization Heat Treatment of Mg-7.68Gd-4.88Y-1.32Nd-0.63Al-0.05Zr Alloy

Homogenization heat treatment of 2099 Al–Li alloy

Microstructural Characterization of the As-Cast and Homogenized Al-Cu-Mg-Ag Alloy

Homogenization heat treatment of Mg-9.0Y-3.0MM-0.6Zr alloy

Microstructure and Hot Deformation Behavior of the Mg-8 wt.% Sn-1.5 wt.% Al Alloy

Homogenization heat treatment of GWN751K magnesium alloy

Effect of Homogenization Treatment on Microstructure of 6063 Alloy

Microstructure, Mechanical Properties and First Principle Calculation of Mg-7Al (-2Sn) Alloys Prepared by Vacuum Die-casting

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Effect of homogenization treatment temperatures on microstructure and properties of 6082 aluminum alloys

Microstructural Evolution of 2026 Aluminum Alloy During Homogenization

Synergistic Effects of Mg Alloying and Subsequent Homogenization Treatment to Improve the Microstructure and Properties of Al-Mg-Mn Alloys

Effect of Zn/Mg ratio on the microstructure and mechanical properties of as-cast Al–Zn–Mg–Cu alloys and the phase transformation during homogenization

The Research of Microstructure and Mechanical Properties of Mg–7Gd–3Y–1Nd–0.5Zn–0.5Zr (wt%) Alloy

Homogenizing and microstructure of Mg-Y-Nd-Zr alloy

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment