Abstract:The laser cladding of the T15 high-speed steel (HSS) was accomplished and its typical microstructure was determined. The microstructure characterization of the clad layer showed three phases of microstructure, planar, cellular and equiaxed growth zones. Electron probe micro-analyzer (EPMA) showed high content in alloying elements at the cellular and equiaxed zones that contained V, C, Cr and W. Further, the analysis at the inter-granular zone presented the highest concentration in elements such as Mo, Cr and W. This showed the presence of carbides which were identified as MCI and M6C at the cellular zone, and M7C3 and M23C6 at the equiaxed and inter-granular zones. The precipitation characterization along the line starting from the substrate and passing through the clad layer identified the austenite matrix and revealed the fluctuation in the alloying elements content, where its amplitude and count increased while passing through the planar zone and hitting the equiaxed zone. Equilibrium phase diagram thermodynamic calculation proved the presence of MCI, M6C and M23C6 which precipitated respectively as the solidification proceeded. The M6C carbide was rich in Fe and W with the presence of V and Cr. MCI carbide had high content of C and V also with dissolved content of W and Cr. Finally, M23C6 carbide contained high amounts of W, Cr and Mo. Scheil–Gulliver simulation model showed the presence of M6C and MCI similar to the equilibrium phase diagram results, additionally, two carbides were revealed and identified as M7C3 and MCII carbides. The M23C6 was absent from the Scheil–Gulliver model. This is due to the assumption that in the Scheil–Gulliver model, the solid stage has no diffusion, and the M23C6 was proved to precipitate in later stages of solidification as shown in the equilibrium phase diagram results. Finally, transmission electron microscopy (TEM) and x-ray diffraction (XRD) showcased the presence of the carbides predicted from the equilibrium phase diagram.

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Evolving Mechanism of Eutectic Carbide in As-Cast AISI M2 High-Speed Steel at Elevated Temperature

Formation and evolution of primary carbides in high-carbon martensitic stainless steel

Transformation behavior of primary MC and M 2 C carbides in Cr4Mo4V steel

Carbide Precipitation Behavior of High‐Alloy Steel During Solidification and Cooling Process

Dissolution Behavior of Eutectic Carbides in Medium-Alloy Steels for Heavy Forgings

Evolution Behavior of Carbides in 2.25Cr-1Mo-0.25v Steel

Effect of Secondary Aerosol Cooling on the Characteristics of Carbides in M42 High‐Speed Steel Produced by the Electroslag Remelting Withdrawal Process

Evolutions of Microstructure by Cerium Treatment in As‐Cast M2 High‐Speed Steel

Evolution of carbides on surface of carburized M50NiL bearing steel

Effect of cerium on the primary carbides and inclusions in electroslag remelted M35 high speed steel

Study on the Formation of Carbide in High ManganeseSteel and its Solution at Elevated Temperature

Evolution and Coarsening of Carbides in 2.25Cr-Lmo Steel Weld Metal During High Temperature Tempering

Refinement of Eutectic Carbides in M2 High Speed Steel by Adjusting Magnetic Flux Density During Magnetic Controlled ESR Process

Athermally induced MC carbide decomposition in gradient M50 bearing steels during electric pulse treatments

Rapid Solidification Microstructure and Carbide Precipitation Behavior in Electron Beam Melted High-Speed Steel

Thermodynamic Calculation and Characterization of Carbide Precipitation in Laser-Deposited Material for High-Speed Steel Alloy

Investigation of Primary Carbides in a Commercial-Sized Electroslag Remelting Ingot of H13 Steel

Optimizing the Morphology of Primary Carbides and Mechanical Properties during Processing Of Cast-Steel (Din Gx210crv12 1) Press-Forming Dies

Morphology and Distribution of Primary Carbides in Forged Cr-Ni-Mo-V/Nb Steel

Evolution of nonmetallic inclusions in 80-t 9CrMoCoB large-scale ingots during electroslag remelting process