Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Effect of Secondary Aerosol Cooling on the Characteristics of Carbides in M42 High‐Speed Steel Produced by the Electroslag Remelting Withdrawal Process

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Refinement of Eutectic Carbides in M2 High Speed Steel by Adjusting Magnetic Flux Density During Magnetic Controlled ESR Process

Effect of titanium and rare earth microalloying on microsegregation, eutectic carbides of M2 high speed steel during ESR process

Effect of Tempering Conditions on Secondary Hardening of Carbides and Retained Austenite in Spray-Formed M42 High-Speed Steel

Effect of cerium on the primary carbides and inclusions in electroslag remelted M35 high speed steel

Morphology Refinement of Eutectic Carbides Assisted by Static Magnetic Field during Laboratory Electroslag Remelting Process

Rapid Solidification Microstructure and Carbide Precipitation Behavior in Electron Beam Melted High-Speed Steel

Homogenization Treatment and Plastic Deformation Improve the Carbide Homogeneity of M42 High-Speed Steel

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Microstructure and mechanical properties of M2 high speed steel produced by electron beam melting

Evolving Mechanism of Eutectic Carbide in As-Cast AISI M2 High-Speed Steel at Elevated Temperature

Evolution of primary carbides during accelerated solidification process of high-carbon martensitic stainless steels

Effect of cooling medium on the κ carbide precipitation behavior, microstructure and impact properties of FeMnAlC low-density steel

Research Progress of Eutectic Carbides in High-Speed Steel

Formation and evolution of primary carbides in high-carbon martensitic stainless steel

Effect of Alloying and Microalloying Elements on Carbides of High-Speed Steel: An Overview

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Effect of RE-Al-N on Structures and Properties of M2 Cast High Speed Steel

Effect of Electroslag Remelting on the Microstructure and Ballistic Penetration Characteristics of an Austenite‐Based Lightweight Steel

Effect of Directional Solidification of Electroslag Remelting on the Microstructure and Primary Carbides in an Austenitic Hot-Work Die Steel