Abstract:Optically transparent materials with p-type electrical conductivity can facilitate the development of transparent electronics and improve the efficiency of photovoltaic solar cells. Sulfide materials represent an interesting alternative to oxides for these applications due to better hole transport properties. Here, transparent and conductive Ba-Cu-S thin films are prepared by combinatorial cosputtering and characterized for their composition, structure, and optoelectronic properties. The conductivity and transparency of these films are found to be strongly dependent on their chemical composition and the substrate temperature during growth. The conductivity of BaCu2S2 and BaCu4S3 can reach 53 S/cm (at 250 degrees C) and 74 S/cm (at 200 degrees C), respectively, which is higher than their solution processed/bulk counterparts. The 90% reflectance corrected transmittance is achieved in the wavelength range 600-1000 nm for BaCu2S2 and 650-1000 nm for BaCu4S3 (at 250 degrees C). These electrical optical properties are comparable with other recently presented transparent p-type conductors, while the 200-350 degrees C processing temperature is low enough to be used in semiconductor devices with limited thermal budgets. Attempts have been made to synthesize the related Sr-Cu-S materials, following the theoretical suggestion of their potential as transparent p-type conductors, but these attempts resulted only in phase-separated SrS and CuxS phases. Alloying BaCu2S2 with Sr on the Ba site on the other hand increases the conductivity to >100 S/cm while only slightly compromising the transparency of the material. To explain the difference between the Ba and the Sr containing copper sulfides, the lower bounds on the SrCu2S2 and SrCu4S3 formation enthalpies are estimated. While the doping of the Ba-Cu-S materials presented here is too large for application in transparent electronics, it is promising for potential use as p-type contact layers in thin film solar cells.

Transparent Inorganic Copper Bromide (cubr) P-Channel Transistors Synthesized from Solution at Room Temperature

Transparent Electronics: Room‐Temperature Solution‐Synthesized P‐type Copper(I) Iodide Semiconductors for Transparent Thin‐Film Transistors and Complementary Electronics (adv. Mater. 34/2018)

Enhanced Performance of P-Channel CuIBr Thin-Film Transistor by ITO Surface Charge-Transfer Doping

P‐17: Low‐Temperature, Solution‐Processed Inorganic P‐channel Cu‐based Thin‐Film Transistors and Circuits

High-performance P-Channel Transistors with Transparent Zn Doped-Cui

High-mobility flexible/transparent p-type copper iodide thin-film transistors and complementary inverters

8‐4: Invited Paper: Transparent Zn Doped‐CuI for High‐Performance P‐channel Thin Film Transistors

Transparent All-Carbon-Nanotube Thin-film Transistors

Fully transparent solution-processed carbon nanotube thin film transistors on a flexible substrate

Amorphous copper iodide: a p-type semiconductor for solution processed p-channel thin-film transistors and inverters

Transparent CsPbBr 3 Quantum Dot Photodetector with a Vertical Transistor Structure

High-Performance p-Type Transparent Conducting CuI−Cu2O Thin Films with Enhanced Hole Mobility, Surface, and Stability

Sputter-Deposited copper iodide thin film transistors with low Operating voltage

Room-temperature synthesized copper iodide thin film as degenerate p-type transparent conductor with a boosted figure of merit

Transparent CsPbBr3 Quantum Dot Photodetector with a Vertical Transistor Structure

Key Roles of Trace Oxygen Treatment for High‐Performance Zn‐Doped CuI P‐channel Transistors

Approaching Theoretical Limits in The Performance of Printed P‐Type Cui Transistors via Room Temperature Vacancy Engineering

Transparent Electronics Using One Binary Oxide for All Transistor Layers

Transparent Ambipolar Organic Thin Film Transistors Based on Multilayer Transparent Source-Drain Electrodes

Optoelectronic Properties of Strontium and Barium Copper Sulfides Prepared by Combinatorial Sputtering

Molecule Charge Transfer Doping for p‐Channel Solution‐Processed Copper Oxide Transistors